ASTM D 2584 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Ignition Loss of Cured Reinforced Resins
Hardcopy , PDF
10-08-2018
English
10-15-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of the ignition loss of cured reinforced resins.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the determination of the ignition loss of cured reinforced resins. This ignition loss can be considered to be the resin content within the limitations of 4.2.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard is used to measure and describe the response of composite material to heat under controlled conditions, but does not by itself incorporate all of the factors required for fire hazard or fire assessments of the composite materials under actual fire conditions.
1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this standard.
| ASTM D 3262 : 2016 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe |
| ASTM D 5364 : 2014 : R2019 | Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units |
| ASTM D 7957/D7957M : 2017 | Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement |
| ASTM D 4097 : 2018 | Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
| ASTM D 5467/D5467M : 1997 : R2017 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using a Sandwich Beam |
| ASTM D 3935 : 2015 | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM D 3753 : 2012 : EDT 1 | Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells |
| ASTM D 3754 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
| ASTM D 5448/D5448M : 2016 | Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders |
| ASTM F 1173 : 2001 : R2018 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 5450/D5450M : 2016 | Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders |
| ASTM D 2344/D2344M : 2016 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
| ASTM D 5961/D5961M : 2017 | Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates |
| ASTM D 5449/D5449M : 2016 | Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders |
| ASTM D 3299 : 2018 | Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
| ASTM D 6783 : 2005 : REV A : R2017 | Standard Specification for Polymer Concrete Pipe |
| ASTM D 3982 : 2008 : R2014 | Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts |
| ASTM C 273/C273M : 2018 | Standard Test Method for Shear Properties of Sandwich Core Materials |
| ASTM C 613 : 2019 | Standard Test Method for Constituent Content of Composite Prepreg by Soxhlet Extraction |
| ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
| ASTM D 3039/D3039M : 2017 | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
| ASTM D 5630 : 2013 | Standard Test Method for Ash Content in Plastics (Withdrawn 2022) |
| ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM D 3489 : 2017 | Standard Test Methods for Microcellular Urethane Materials |
| ASTM D 3517 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
| ASTM D 7745 : 2011 | Standard Practice for Testing Pultruded Composites |
| ASTM D 4255/D4255M : 2015 : REV A | Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method |
| ASTM D 7078/D7078M : 2012 | Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6041 : 2018 | Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings |
| ASTM C 581 : 2015 | Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service |
| ASTM E 1556 : 2012 | Standard Specification for Epoxy Resin System for Composite Skin, Honeycomb Sandwich Panel Repair |
| ASTM D 5379/D5379M : 2012 | Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method |
| ASTM D 2734 : 2016 | Standard Test Methods for Void Content of Reinforced Plastics |
| ASTM C 582 : 2009 : R2016 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
| ASTM C 297/C297M : 2016 | Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions |
| ASTM C 364/C364M : 2016 | Standard Test Method for Edgewise Compressive Strength of Sandwich Constructions |
| ASTM D 6416/D6416M : 2016 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load |
| ASTM D 7248/D7248M : 2012 : R2017 | Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens |
| ASTM D 3410/D3410M : 2016 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
| ASTM D 6484/D6484M : 2014 | Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates |
| ASTM D 7905/D7905M : 2019 | Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.