ASTM D 2578 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
Hardcopy , PDF
03-17-2023
English
01-25-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
Note 1:This test method and the specified reagents were specifically developed for polyethylene and polypropylene films. It is possible to utilize this test method and the specified reagents for films composed of other polymers, but this can affect the surface energies of the gas-liquid and solid-liquid interfaces, which will affect the contact angle and wetting tension. The applicability and significance for use of non-polyolefin materials must be established by the user.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8.
Note 2:This test method is equivalent to ISO 8296.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM F 22 : 2013 | Standard Test Method for Hydrophobic Surface Films by the Water-Break Test |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 7541 : 2011 : R2015 | Standard Practice for Estimating Critical Surface Tensions |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM F 21 : 2014 | Standard Test Method for Hydrophobic Surface Films by the Atomizer Test |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM D 6105 : 2004 : R2019 | Standard Practice for Application of Electrical Discharge Surface Treatment (Activation) of Plastics for Adhesive Bonding |
| ASTM D 4649 : 2020 | Standard Guide for Use of Stretch Films and Wrapping Application |
| ASTM F 22 : 2021 | Standard Test Method for Hydrophobic Surface Films by the Water-Break Test |
| ASTM D 2673 : 2014 : R2022 | Standard Specification for Oriented Polypropylene Film |
| ASTM D 7541 : 2011 : R2022 | Standard Practice for Estimating Critical Surface Tensions |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.