• There are no items in your cart

ASTM D 2422 : 1997 : R2018

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Classification of Industrial Fluid Lubricants by Viscosity System

Available format(s)

Hardcopy , PDF

Superseded date

05-29-2024

Superseded by

ASTM D 2422 : 2024

Language(s)

English

Published date

10-01-2018

US$66.00
Excluding Tax where applicable

Committee
D 02
DocumentType
Standard
Pages
2
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This classification is applicable to all petroleum-base fluid lubricants and to those nonpetroleum materials which may be readily blended to produce fluid lubricants of a desired viscosity, that is, lubricants for bearings, gears, compressor cylinders, hydraulic fluids, etc.

1.2This classification is applicable to fluids ranging in kinematic viscosity from 2 cSt to 3200 cSt (mm2/s) as measured at a reference temperature of 40 °C. In the category of petroleum-base fluids, this covers the range from kerosene to heavy cylinder oils.

1.3Fluids of either lesser or greater viscosity than the range described in 1.2 are, at present, seldom used as industrial lubricants. Should industrial practices change, then this system, based on a mathematical series of numbers, may be extended to retain its orderly progression.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 5763 : 2011 : R2016 Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware
ASTM D 4293 : 2015 : EDT 1 Standard Specification for Phosphate Ester Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications
ASTM D 665 : 2014 : EDT 1 Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D 6709 : 2015 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)
ASTM D 8029 : 2018 Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids
ASTM D 6158 : 2018 Standard Specification for Mineral Hydraulic Oils
ASTM D 6080 : 2018 : REV A Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids
ASTM D 4304 : 2017 Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines
ASTM D 4378 : 2013 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6224 : 2016 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 6618 : 2016 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine
ASTM D 7044 : 2015 Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids (Withdrawn 2024)
ASTM D 665 : 2023 Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D 6158 : 2023 Standard Specification for Mineral Hydraulic Oils
ASTM D 6618 : 2023 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine
ASTM D 8324 : 2021 Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit
ASTM D 4304 : 2022 Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines
ASTM D 6709 : 2024 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)
ASTM D 8029 : 2023 Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids
ASTM D 4293 : 2022 Standard Specification for Phosphate Ester-Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications
ASTM D 4378 : 2024 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6224 : 2023 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 5763 : 2022 : REV A Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.