ASTM D 2369 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Volatile Content of Coatings
11-11-2014
07-01-2010
CONTAINED IN VOL. 06.01, 2017 Specifies a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 ± 5°C for 60 min.
Note 1—The coatings used in these round-robin studies represented air-dried, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems.
1.2 Sixty minutes at 110 ± 5°C is a general purpose test method based on the precision obtained with both solventborne and waterborne coatings (see Section 9).
1.3 This test method is viable for coatings wherein one or more parts may, at ambient conditions, contain liquid coreactants that are volatile until a chemical reaction has occurred with another component of the multi-package system.
Note 2—Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and allow the specimens to stand at room temperature for 1 h prior to placing them into the oven.
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 7805 : 2013 | Standard Terminology for Printing Ink Vehicles and Related Materials |
| ASTM D 5403 : 1993 : R2013 | Standard Test Methods for Volatile Content of Radiation Curable Materials |
| ASTM F 940 : 1999 : R2013 | Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding |
| ASTM D 7232 : 2006 : R2016 | Standard Test Method for Rapid Determination of the Nonvolatile Content of Coatings by Loss in Weight |
| ASTM D 6419 : 2000 : R2017 | Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks |
| ASTM D 5327 : 1997 : R2013 | Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under General Laboratory Conditions |
| ASTM D 4302 : 2014 | Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints |
| ASTM D 5087 : 2002 : R2014 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| ASTM D 4713 : 2012 | Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems |
| ASTM D 2205 : 2015 | Standard Guide for Selection of Tests for Traffic Paints |
| ASTM C 309 : 2011 | Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete |
| ASTM C 461 : 2017 | Standard Test Methods for Mastics and Coatings Used With Thermal Insulation |
| ASTM D 4764 : 2001 : R2016 | Standard Test Method for Determination by X-ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint |
| ASTM D 6583 : 2013 : R2019 | Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption |
| ASTM D 5286 : 2001 : R2017 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 4209 : 2007 : R2019 | Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 6763 : 2016 | Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents |
| ASTM D 5325 : 2003 : R2014 | Standard Test Method for Determination of Weight Percent Volatile Content of Water-Borne Aerosol Paints |
| ASTM C 156 : 2017 | Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete |
| ASTM D 6266 : 2000 : REV A : R2017 | Standard Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| ASTM C 1315 : 2011 | Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete |
| ASTM D 4143 : 2016 | Standard Guide for Testing Latex Vehicles |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 5201 : 2005 : REV A : R2014 | Standard Practice for Calculating Formulation Physical Constants of Paints and Coatings |
| ASTM D 6886 : 2018 | Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography |
| ASTM D 5009 : 2002 : R2017 | Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions |
| ASTM D 2698 : 2005 : R2015 | Standard Test Method for Determination of the Pigment Content of Solvent-Reducible Paints by High-Speed Centrifuging |
| ASTM D 3960 : 2005 : R2018 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM D 7270 : 2007 : R2013 | Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings |
| ASTM D 5324 : 2016 | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 6093 : 1997 : R2016 | Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |
| ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM D 5066 : 1991 : R2017 | Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis |
| ASTM D 2697 : 2003 : R2014 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 180 : 2003 | Standard Practice for Determining the Precision of ASTM Methods for Analysis and Testing of Industrial and Specialty Chemicals (Withdrawn 2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.