ASTM D 226/D226M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
Hardcopy , PDF
08-25-2023
English
07-07-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 08
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers asphalt-saturated organic felts, with or without perforations, intended to be used with asphalts conforming to the requirements of Specification D312/D312M in the construction of built-up roofs, and with asphalts conforming to the requirements of Specification D449/D449M in the construction of water proofing systems.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 3617/D3617M : 2017 : R2022 | Standard Practice for Sampling and Analysis of Built-Up Roof Systems During Application |
| ASTM D 4932/D4932M : 1989 : R2019 | Standard Test Method for Fastener Rupture and Tear Resistance of Roofing and Waterproofing Sheets, Roll Roofing, and Shingles |
| ASTM E 3127 : 2022 | Standard Guide for Specifying Water Vapor Transmission Material Properties of Water-Resistive Barriers and Air Barriers |
| ASTM D 449/D449M : 2003 : R2021 | Standard Specification for Asphalt Used in Dampproofing and Waterproofing |
| ASTM D 2626/D2626M : 2004 : R2020 | Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing |
| ASTM C 981 : 2020 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
| ASTM C 240 : 2021 | Standard Test Methods for Testing Cellular Glass Insulation Block |
| ASTM D 6622/D6622M : 2020 | Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems |
| ASTM D 7000 : 2019 : REV A | Standard Test Method for Sweep Test of Emulsified Asphalt Surface Treatment Samples |
| ASTM E 2556/E2556M : 2010 : R2022 | Standard Specification for Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment |
| ASTM E 2266 : 2022 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM D 5100/D5100M : 1995 : REV A : R2018 | Standard Test Method for Adhesion of Mineral Aggregate to Hot Bitumen |
| ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 6136/D6136M : 2015 : R2021 | Standard Test Method for Kerosine Number of Unsaturated (Dry) Felt by Vacuum Method |
| ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 6136/D6136M : 2015 | Standard Test Method for Kerosine Number of Unsaturated (Dry) Felt by Vacuum Method |
| ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM D 70 : 2018 : REV A | Standard Test Method for Density of Semi-Solid Asphalt Binder (Pycnometer Method) |
| ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.