ASTM D 2162 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards
04-15-2021
English
05-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2015 Determines the calibration of master viscometers and viscosity oil standards, both of which may be used to calibrate routine viscometers as described in Test Method D 445 and Specifications D 446 over the temperature range from 15 to 100 degrees C.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This practice covers the calibration of master viscometers and viscosity oil standards, both of which may be used to calibrate routine viscometers as described in Test Method D445 and Specifications D446 over the temperature range from 15 °C to 100 °C.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1The SI-based units for calibration constants and kinematic viscosities are mm2/s2 and mm 2/s, respectively.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7483 : 2013 : REV A | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 7483 : 2013 : REV A : R2017 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
| ASTM D 446 : 2012 | Standard Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers |
| 17/30366325 DC : 0 | BS EN ISO 3104 - PETROLEUM PRODUCTS - TRANSPARENT AND OPAQUE LIQUIDS - DETERMINATION OF KINEMATIC VISCOSITY AND CALCULATION OF DYNAMIC VISCOSITY |
| ASTM D 8092 : 2017 | Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer |
| ASTM D 7945 : 2016 : REDLINE | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer |
| ASTM D 7483 : 2013 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
| IP PM EJ : 2014 | DETERMINATION OF KINEMATIC VISCOSITY OF AVIATION TURBINE FUELS - MANUAL AND AUTOMATED METHOD |
| ASTM D 446 : 2012 : R2017 | Standard Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers |
| NBR 14173 : 2012 | MOTOR OILS AND BASE OILS - DETERMINATION OF APPARENT VISCOSITY BETWEEN -5 DEGREES C AND -35 DEGREES C BY THE SIMULATOR COLD START |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 1590 : 1960 : R1977 : EDT 2 | Test Methods for Surface Tension of Water and Waste Water |
| ASTM E 644 : 2011 : REDLINE | Standard Test Methods for Testing Industrial Resistance Thermometers |
| ASTM D 1480 : 2015 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer |
| ASTM E 1137 : 1997 | Standard Specification for Industrial Platinum Resistance Thermometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.