ASTM D 2068 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Filter Blocking Tendency
Hardcopy , PDF
05-15-2024
English
10-08-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers three procedures for the determination of the filter blocking tendency (FBT) and filterability of middle distillate fuel oils and liquid fuels such as biodiesel and biodiesel blends. The three procedures and associated filter types are applicable to fuels within the viscosity range of 1.3 mm2 to 6.0 mm2/s at 40 °C.
Note 1:ASTM specification fuels falling within the scope of this test method are: Specification D396 Grades No 1 and 2; Specification D975 Grades 1-D, low sulfur 1-D and 2-D; Specification D2880 Grades 1-GT and 2-GT; Specification D6751.
1.2This test method is not applicable to fuels that contain free (undissolved) water (see 7.3).
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
| ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 8386 : 2021 | Standard Test Method for Determining Enhanced Filter Blocking Tendency (EFBT) |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4176 : 2021 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
| ASTM D 396 : 1998 | Standard Specification for Fuel Oils |
| ASTM D 4860 : 2022 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 975 : 2019 : REV B | Standard Specification for Diesel Fuel |
| ASTM D 6426 : 2022 | Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils |
| ASTM D 975 : 2021 | Standard Specification for Diesel Fuel |
| ASTM D 975 : 2023 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 6708 : 2024 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2023 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 975 : 2020 : REV C | Standard Specification for Diesel Fuel |
| ASTM D 6300 : 2023 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2880 : 2023 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 2021 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6426 : 2013 | Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils |
| ASTM D 4176 : 2022 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 6708 : 2001 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2021 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6751 : 2023 : REV A | Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels |
| ASTM D 6426 : 2001 | Standard Test Method for Determining Filterability of Distillate Fuel Oils |
| ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 4176 : 2021 : REV A | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4176 : 2020 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 6751 : 2023 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 396 : 2009 | Standard Specification for Fuel Oils |
| ASTM D 4860 : 2014 : R2019 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 975 : 2023 | Standard Specification for Diesel Fuel |
| ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6426 : 2018 | Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils |
| ASTM D 396 : 2024 | Standard Specification for Fuel Oils |
| ASTM D 4177 : 2022 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6708 : 2019 : REV A : EDT 1 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6300 : 2024 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.