ASTM D 189 : 2006 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Conradson Carbon Residue of Petroleum Products
Hardcopy , PDF
06-14-2024
English
12-11-2019
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the determination of the amount of carbon residue (Note 1) left after evaporation and pyrolysis of an oil, and is intended to provide some indication of relative coke-forming propensities. This test method is generally applicable to relatively nonvolatile petroleum products which partially decompose on distillation at atmospheric pressure. Petroleum products containing ash-forming constituents as determined by Test Method D482 or IP Method 4 will have an erroneously high carbon residue, depending upon the amount of ash formed (Note 2 and Note 4).
Note 1:The term carbon residue is used throughout this test method to designate the carbonaceous residue formed after evaporation and pyrolysis of a petroleum product under the conditions specified in this test method. The residue is not composed entirely of carbon, but is a coke which can be further changed by pyrolysis. The term carbon residue is continued in this test method only in deference to its wide common usage.
Note 2:Values obtained by this test method are not numerically the same as those obtained by Test Method D524. Approximate correlations have been derived (see Fig. X1.1), but need not apply to all materials which can be tested because the carbon residue test is applied to a wide variety of petroleum products.
Note 3:The test results are equivalent to Test Method D4530, (see Fig. X1.2).
Note 4:In diesel fuel, the presence of alkyl nitrates such as amyl nitrate, hexyl nitrate, or octyl nitrate causes a higher residue value than observed in untreated fuel, which can lead to erroneous conclusions as to the coke forming propensity of the fuel. The presence of alkyl nitrate in the fuel can be detected by Test Method D4046.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6710 : 2021 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM D 2416 : 2020 | Standard Test Method for Coking Value of Tar and Pitch (Modified Conradson) |
ASTM D 6751 : 2023 : REV A | Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels |
ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 6074 : 2015 : R2022 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 524 : 2015 : R2019 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products |
ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 4175 : 2020 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM E 133 : 1992 : R2016 | Standard Specification for Distillation Equipment |
ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 482 : 2013 | Standard Test Method for Ash from Petroleum Products |
ASTM D 4175 : 2020 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4530 : 2015 : R2020 | Standard Test Method for Determination of Carbon Residue (Micro Method) |
ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2022 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2023 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2022 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM E 133 : 1992 : R2022 | Standard Specification for Distillation Equipment |
ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4175 : 2023 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2023 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2019 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2022 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 524 : 2015 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products |
ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4530 : 2015 | Standard Test Method for Determination of Carbon Residue (Micro Method) |
ASTM D 4177 : 2022 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.