ASTM D 1796 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
Hardcopy , PDF
11-11-2014
English
06-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2018 Specifies the laboratory determination of water and sediment in fuel oils in the range from 0% to 30% volume by means of the centrifuge procedure.
| Committee |
D 02
|
| DevelopmentNote |
Also numbered as API MPM CH10.6. (08/2013)
|
| DocumentType |
Test Method
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2011
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 30 % volume by means of the centrifuge procedure.
Note 1—With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D95 (API MPMS Chapter 10.5) or Test Method D473 (API MPMS Chapter 10.1) may be used.
Note 2—API MPMS Chapter 10.6 (Test Method D1796) along with API MPMS Chapter 10.3 (Test Method D4007) formerly superseded API Standard 2548.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 6.1.
| ASTM D 1290 : 1995 : R2015 | Standard Test Method for Sediment in Water-Emulsion Polishes by Centrifuge |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 6666 : 2004 : R2019 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM D 2711 : 2017 | Standard Test Method for Demulsibility Characteristics of Lubricating Oils |
| ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 4418 : 2017 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
| ASTM D 2158 : 2016 : REV A : EDT 1 | Standard Test Method for Residues in Liquefied Petroleum (LP) Gases |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 6618 : 2016 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
| API MPM CH10.5 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 10.5: STANDARD TEST METHOD FOR WATER IN PETROLEUM PRODUCTS AND BITUMINOUS MATERIALS BY DISTILLATION |
| ISO 5272:1979 | Toluene for industrial use — Specifications |
| API MPM CH8.1 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
| API MPM CH8.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.2: STANDARD PRACTICE FOR AUTOMATIC SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.