ASTM D 1683/D1683M : 2017 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Failure in Sewn Seams of Woven Fabrics
Hardcopy , PDF
04-29-2022
English
04-12-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 13
|
| DocumentType |
Test Method
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method measures the sewn seam strength in woven fabrics by applying a force perpendicular to the sewn seams.
1.1.1The axis perpendicular to the sewn seam can represent either the warp yarn axis or filling yarn axis, the same axis tested when using grab Test Method D5034.
1.1.1.1This test method is applicable to sewn seams obtained from a previously sewn article or seams sewn with fabric samples using one of two specific seam assemblies as shown in Table 1.
Note 1:When the performance of a woven textile structure requires data to indicate the maximum seam strength that will result in the failure of fabric on either side of seam, the standard seam can be changed to use the Lapped seam type construction with two or more rows of stitching: Lsc-2; Lsc-3; Lsc-4; and the maximum number of stitches per inch that can be used. (See Practice D6193.)
1.2This test method is used when the maximum breaking force measurement to rupture of a woven fabric sewn seam is required.
1.2.1This test method is used when the seam efficiency measurement of a woven fabric sewn seam is required.
1.2.2This test method is used to identify the sewn seam strength threshold at which the failure of the stitching occurs, without damage to the fabric, so that the textile product can be repaired.
1.2.3This test method is used to identify the force at which seam strength results in slippage and displacement of warp yarns, filling yarns, or any combination of these yarns.
1.3This test method does not predict actual wear performance of a seam.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2407 : 2020 | Standard Specification for Surgical Gowns Intended for Use in Healthcare Facilities |
| ASTM F 3343 : 2020 | Standard Consumer Safety Specification for Infant Bathers |
| ASTM F 3352 : 2019 | Standard Specification for Isolation Gowns Intended for Use in Healthcare Facilities |
| ASTM D 204 : 2002 : R2021 | Standard Test Methods for Sewing Threads |
| ASTM F 406 : 2019 | Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM D 7722 : 2017 | Standard Terminology Relating to Industrial Textile Stitches and Seams |
| ASTM D 1776 : 1967 : EDT 1 | Standard Method Of Conditioning Textiles And Textile Products For Testing |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 6193 : 1997 | Standard Practice for Stitches and Seams |
| ASTM D 7722 : 2011 | Standard Terminology Relating to Industrial Textile Stitches and Seams |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 5034 : 2009 : R2017 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
| ASTM D 5034 : 2021 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
| ASTM D 123 : 2001 | Standard Terminology Relating to Textiles |
| ASTM D 5034 : 1995 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.