ASTM C 722 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Chemical-Resistant Monolithic Floor Surfacings
Hardcopy , PDF
06-29-2023
English
04-17-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the requirements for aggregate-filled, resin-based, monolithic surfacings for use over concrete floors in areas where chemical resistance and the protection of concrete are required.
1.2The application methods for these floor surfacings include troweled, broadcast, slurry broadcast, self-leveling, sprayed, and reinforced. The resin chemistries include epoxy, urethane, polyester, and vinyl ester.
1.3Floor surfacings used as vessel linings are excluded from this specification.
1.4The values stated in SI units are to be regarded as the standard. The values in parenthesis are provided for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 267 : 1997 | Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
| ASTM C 580 : 1998 | Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM D 6132 : 1997 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Over Concrete Using an Ultrasonic Gage |
| ASTM D 2047 : 1999 | Standard Test Method for Static Coefficient of Friction of Polish-Coated Floor Surfaces as Measured by the James Machine |
| ASTM D 2047 : 2017 | Standard Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine |
| ASTM C 1486 : 2018 | Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings |
| ASTM C 904 : 1998 | Standard Terminology Relating to Chemical-Resistant Nonmetallic Materials |
| ASTM C 307 : 2018 | Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacings |
| ASTM F 2508 : 2011 | Standard Practice for Validation and Calibration of Walkway Tribometers Using Reference Surfaces |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1308 : 1979 : R1981 : EDT 1 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1308 : 1987 : R1998 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 6132 : 2013 : R2022 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM C 307 : 2023 | Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacings |
| ASTM F 2508 : 2016 : EDT 1 | Standard Practice for Validation, Calibration, and Certification of Walkway Tribometers Using Reference Surfaces |
| ASTM C 579 : 2023 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 579 : 2018 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.