ASTM C 666/C666M : 2015
Current
The latest, up-to-date edition.
Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024)
Hardcopy , PDF
English
04-08-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of the resistance of concrete specimens to rapidly repeated cycles of freezing and thawing in the laboratory by two different procedures: Procedure A, Rapid Freezing and Thawing in Water, and Procedure B, Rapid Freezing in Air and Thawing in Water.
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of the resistance of concrete specimens to rapidly repeated cycles of freezing and thawing in the laboratory by two different procedures: Procedure A, Rapid Freezing and Thawing in Water, and Procedure B, Rapid Freezing in Air and Thawing in Water. Both procedures are intended for use in determining the effects of variations in the properties of concrete on the resistance of the concrete to the freezing-and-thawing cycles specified in the particular procedure. Neither procedure is intended to provide a quantitative measure of the length of service that may be expected from a specific type of concrete.
1.2The values stated in either inch-pound units or SI units shall be regarded separately as standard. The SI units are shown in brackets. The values stated may not be exact equivalents; therefore each system must be used independently of the other. Combining values from the two units may result in nonconformance.
1.3All material in this test method not specifically designated as belonging to Procedure A or Procedure B applies to either procedure.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 1116/C1116M : 2010 : REV A : R2015 | Standard Specification for Fiber-Reinforced Concrete |
| ASTM D 6684 : 2018 | Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Systems |
| ASTM C 330/C330M : 2017 : REV A | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 1364 : 2023 | Standard Specification for Architectural Cast Stone |
| ASTM C 341/C341M : 2018 | Standard Practice for Preparation and Conditioning of Cast, Drilled, or Sawed Specimens of Hydraulic-Cement Mortar and Concrete Used for Length Change Measurements |
| ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM E 1512 : 2001 : R2015 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
| ASTM C 1856/C1856M : 2017 | Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete |
| ASTM C 1776/C1776M : 2017 : R2022 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
| ASTM C 1670/C1670M : 2021 : REV B | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM D 8139 : 2017 | Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM C 1325 : 2022 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
| ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 1646/C1646M : 2016 | Standard Practice for Making and Curing Test Specimens for Evaluating Resistance of Coarse Aggregate to Freezing and Thawing in Air-Entrained Concrete |
| ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
| ASTM C 457/C457M : 2023 | Standard Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete |
| ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ASTM C 457/C457M : 2023 : REV A | Standard Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete |
| ASTM D 8139 : 2023 | Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM C 1670/C1670M : 2023 : REV A | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM E 1512 : 2001 : R2023 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
| ASTM C 1325 : 2022 : EDT 1 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM C 33/C33M : 2023 | Standard Specification for Concrete Aggregates |
| ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 494/C494M : 2019 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM C 215 : 2019 | Standard Test Method for Fundamental Transverse, Longitudinal, and<brk/> Torsional Resonant Frequencies of Concrete Specimens |
| ASTM C 494/C494M : 2010 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 295 : 1998 | Standard Guide for Petrographic Examination of Aggregates for Concrete |
| ASTM C 215 : 1997 : EDT 1 | Standard Test Method for Fundamental Transverse, Longitudinal, and Torsional Frequencies of Concrete Specimens |
| ASTM C 670 : 2015 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.