ASTM C 403/C403M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
Hardcopy , PDF
07-12-2023
English
01-25-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
1.2This test method is suitable for use only when tests of the mortar fraction will provide the information required.
1.3This test method may also be applied to prepared mortars and grouts.
1.4This test method is applicable under controlled laboratory conditions, as well as under field conditions.
1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1384 : 2018 : EDT 1 | Standard Specification for Admixtures for Masonry Mortars |
| ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 192/C192M : 2019 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM C 935 : 2019 | Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast |
| ASTM C 1679 : 2022 | Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry |
| ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 1698 : 2019 | Standard Test Method for Autogenous Strain of Cement Paste and Mortar |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 827/C827M : 2016 | Standard Test Method for Change in Height at Early Ages of Cylindrical Specimens of Cementitious Mixtures |
| ASTM C 979/C979M : 2016 | Standard Specification for Pigments for Integrally Colored Concrete |
| ASTM C 1810/C1810M : 2022 | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ASTM C 31/C31M : 2022 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
| ASTM C 1579 : 2021 | Standard Test Method for Evaluating Plastic Shrinkage Cracking of Restrained Fiber Reinforced Concrete (Using a Steel Form Insert) |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 1753/C1753M : 2021 : REV A | Standard Practice for Evaluating Early Hydration of Hydraulic Cementitious Mixtures Using Thermal Measurements |
| ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ASTM C 1602/C1602M : 2022 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 173/C173M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| ASTM C 173/C173M : 2009 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| ASTM E 2251 : 2007 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM E 2251 : 2003 : REV A | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 2251 : 2003 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM E 2251 : 2014 : R2021 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM E 2251 : 2010 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM E 2251 : 2011 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM E 2251 : 2014 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM D 1558 : 1999 | Standard Test Method for Moisture Content Penetration Resistance Relationships of Fine-Grained Soils |
| ASTM C 802 : 2014 | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
| ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM D 1558 : 1999 : R2004 : EDT 1 | Standard Test Method for Moisture Content Penetration Resistance Relationships of Fine-Grained Soils |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 802 : 2014 : R2022 | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
| ASTM D 1558 : 2010 | Standard Test Method for Moisture Content Penetration Resistance Relationships of Fine-Grained Soils (Withdrawn 2019) |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.