ASTM C 183/C183M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
Hardcopy , PDF
06-30-2023
English
10-20-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice covers procedures for sampling and for the amount of testing of hydraulic cement after it has been manufactured and is ready to be offered for sale.
| Committee |
C 01
|
| DocumentType |
Standard Practice
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers procedures for sampling and for the amount of testing of hydraulic cement after it has been manufactured and is ready to be offered for sale.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard IEEE/ASTM SI 10, Values are stated in only SI units when inch-pound units are not used in practice
1.3The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1141/C1141M : 2015 | Standard Specification for Admixtures for Shotcrete (Withdrawn 2024) |
| ASTM C 845/C845M : 2018 | Standard Specification for Expansive Hydraulic Cement |
| ASTM C 266 : 2021 | Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles |
| ASTM D 242/D242M : 2019 | Standard Specification for Mineral Filler for Asphalt Mixtures |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 359 : 2021 | Standard Test Method for Early Stiffening of Hydraulic-Cement (Mortar Method) |
| ASTM C 1697 : 2021 | Standard Specification for Blended Supplementary Cementitious Materials |
| ASTM C 10/C10M : 2019 | Standard Specification for Natural Cement |
| ASTM C 1600/C1600M : 2019 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 1365 : 2018 | Standard Test Method for Determination of the Proportion of Phases in Portland Cement and Portland-Cement Clinker Using X-Ray Powder Diffraction Analysis |
| ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 807 : 2021 | Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle |
| ASTM C 451 : 2021 | Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method) |
| ASTM C 191 : 2021 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
| ACI PRC-225:2023 | Guide to the Selection and Use of Hydraulic Cements |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 451 : 2019 | Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method) |
| ASTM C 191 : 2019 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
| ASTM C 807 : 2021 | Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle |
| ASTM C 266 : 2021 | Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles |
| ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 1506 : 2001 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 1357 : 2002 | Standard Test Methods for Evaluating Masonry Bond Strength |
| ASTM C 1506 : 2016 : REV B | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 451 : 2021 | Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method) |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 1157/C1157M : 2020 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM C 1506 : 2016 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 807 : 2020 | Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle |
| ASTM C 1506 : 2003 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 266 : 2020 | Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles |
| ASTM C 1357 : 2005 | Standard Test Methods for Evaluating Masonry Bond Strength |
| ASTM C 1506 : 2017 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 191 : 2021 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
| ASTM C 1357 : 1998 : REV A | Standard Test Methods for Evaluating Masonry Bond Strength |
| ASTM C 1357 : 2004 : REV A | Standard Test Methods for Evaluating Masonry Bond Strength |
| ASTM C 114 : 2009 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 1357 : 2004 | Standard Test Methods for Evaluating Masonry Bond Strength |
| ASTM C 1357 : 2009 | Standard Test Methods for Evaluating Masonry Bond Strength (Withdrawn 2016) |
| ASTM C 1506 : 2009 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 1506 : 2016 : REV A | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 1506 : 2008 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.