ASTM C 1713 : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Mortars for the Repair of Historic Masonry
Hardcopy , PDF
08-10-2024
English
04-01-2023
Committee |
C 15
|
DocumentType |
Standard
|
Pages |
11
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers mortar for the repair of masonry constructed with methods and materials that pre-date the origination of current standards of construction. The mortar may be used for non-structural purposes such as repointing of the masonry, or for structural purposes such as, but not restricted to, re-construction or repair of mortar joints that contribute to the structural integrity of the masonry.
1.2Masonry includes the following units laid in mortar: (1) cast stone, (2) clay brick and tile, (3) concrete masonry, (4) natural stone, (5) terra cotta, and (6) calcium silicate.
1.3This specification may be used to pre-qualify mortar for a project.
1.4Mortars tested using this specification are laboratory-prepared mortars and do not represent in-place, site mortars.
1.5This specification provides a basis for the design of an appropriate mortar formulation based upon performance, material and aesthetic requirements. Use of this specification requires a thorough understanding of the function, maintenance, and repair requirements for the preservation and continued performance of the masonry assembly in the context of the assembly’s structure, water management, and long-term performance.
1.6The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 2260 : 2021 : REV A | Standard Guide for Repointing (Tuckpointing) Historic Masonry |
ASTM C 144 : 2018 | Standard Specification for Aggregate for Masonry Mortar |
ASTM C 150/C150M : 2024 | Standard Specification for Portland Cement |
ASTM C 270 : 1919 : REV A : EDT 1 | Standard Specification for Mortar for Unit Masonry |
ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM C 1180 : 2024 | Standard Terminology of Mortar and Grout for Unit Masonry |
ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
ASTM C 305 : 2014 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1157/C1157M : 2023 | Standard Performance Specification for Hydraulic Cement |
ASTM C 5 : 2018 | Standard Specification for Quicklime for Structural Purposes |
ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
ASTM C 780 : 2020 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 10/C10M : 2019 | Standard Specification for Natural Cement |
ASTM E 96/E96M : 2023 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM C 5 : 2024 | Standard Specification for Quicklime for Structural Purposes |
ASTM E 96/E96M : 2024 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM C 10/C10M : 2024 | Standard Specification for Natural Cement |
ASTM C 1400 : 2011 : R2017 | Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls |
ASTM C 1384 : 2023 | Standard Specification for Admixtures for Masonry Mortars |
ASTM C 207 : 2018 | Standard Specification for Hydrated Lime for Masonry Purposes |
ASTM C 109/C109M : 2020 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
ASTM C 1403 : 2022 : REV A | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
ASTM C 109/C109M : 2023 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50mm [2 in.] Cube Specimens) |
ASTM C 136/C136M : 2014 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
ASTM C 780 : 2023 | Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 1180 : 2022 | Standard Terminology of Mortar and Grout for Unit Masonry |
ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
ASTM C 948 : 1981 : R2023 | Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete |
ASTM C 216 : 2023 | Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale) |
ASTM C 1384 : 2018 : EDT 1 | Standard Specification for Admixtures for Masonry Mortars |
ASTM C 110 : 2024 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM C 1093 : 2023 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM C 207 : 2024 | Standard Specification for Hydrated Lime for Masonry Purposes |
ASTM C 1400 : 2023 | Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls |
ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
ASTM C 595/C595M : 2024 | Standard Specification for Blended Hydraulic Cements |
ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
ASTM C 216 : 2022 | Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale) |
ASTM C 780 : 2018 : REV A | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 948 : 1981 : R2016 | Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete |
ASTM C 780 : 2019 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
ASTM C 270 : 2024 | Standard Specification for Mortar for Unit Masonry |
ASTM C 1093 : 2022 : REV A | Standard Practice for Accreditation of Testing Agencies for Masonry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.