ASTM C 1440 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems
Hardcopy , PDF
10-07-2021
English
11-21-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 04
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers thermoplastic elastomeric (TPE) gasket materials for preformed elastomeric gaskets used in shielded and non-shielded mechanical couplings. These couplings are used in gravity flow drain, waste, and vent (DWV), sewer, sanitary, and storm plumbing systems. They include couplings to join similar and dissimilar piping sizes and material.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASME A112.36.2/CSA B79.2:2022 | Cleanouts |
| ASTM C 1461 : 2008 : R2017 | Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use |
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
| ASTM D 5964 : 2015 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
| ASTM D 5964 : 2016 : R2021 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
| ASTM A 644 : 1998 | Standard Terminology Relating to Iron Castings |
| ASTM D 1149 : 2015 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 5964 : 1996 | Standard Practice for Rubber IRM 902 and IRM 903 Replacement Oils for ASTM No. 2 and ASTM No. 3 Oils |
| ASTM D 5964 : 2016 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
| ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
| ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 1415 : 1968 | Standard Test Method for International Hardness Of Vulcanized Rubber |
| ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1149 : 1978 : REV A | Standard Test Method for Rubber Deterioration - Surface Ozone Cracking In A Chamber ( Flat Specimen) |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 5964 : 2015 : REV A | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.