ASTM C 1383 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring the P-Wave Speed and the Thickness of Concrete Plates Using the Impact-Echo Method
02-09-2024
English
09-17-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.02, 2015 Outlines procedures for determining the thickness of concrete slabs, pavements, bridge decks, walls, or other plate-like structure using the impact-echo method.
| Committee |
C 09
|
| DocumentType |
Redline
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers procedures for determining the thickness of concrete slabs, pavements, bridge decks, walls, or other plate-like structure using the impact-echo method.
1.2The following two procedures are covered in this test method:
1.2.1Procedure A: P-Wave Speed Measurement—This procedure measures the time it takes for the P-wave generated by a short-duration, point impact to travel between two transducers positioned a known distance apart along the surface of a structure. The P-wave speed is calculated by dividing the distance between the two transducers by the travel time.
1.2.2Procedure B: Impact-Echo Test—This procedure measures the frequency at which the P-wave generated by a short-duration, point impact is reflected between the parallel (opposite) surfaces of a plate. The thickness is calculated from this measured frequency and the P-wave speed obtained from Procedure A.
1.2.3Unless specified otherwise, both Procedure A and Procedure B must be performed at each point where a thickness determination is made.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1740 : 2016 : REDLINE | Standard Practice for Evaluating the Condition of Concrete Plates Using the Impulse-Response Method |
| ACI 117M : 2010 | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
| ACI MNL 3 : 0 | GUIDE TO THE CODE FOR ASSESSMENT, REPAIR, AND REHABILITATION OF EXISTING CONCRETE STRUCTURES |
| ACI 117:2010(R2015) | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
| NACE SP 03 08 : 2008(R2018) | INSPECTION METHODS FOR CORROSION EVALUATION OF CONVENTIONALLY REINFORCED CONCRETE STRUCTURES |
| ACI 117:2010 | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
| ACI 364.1R : 2007 | GUIDE FOR EVALUATION OF CONCRETE STRUCTURES PRIOR TO REHABILITATION |
| ACI 222R : 2001 | PROTECTION OF METALS IN CONCRETE AGAINST CORROSION |
| ACI 437R : 2003 | STRENGTH EVALUATION OF EXISTING CONCRETE BUILDINGS |
| CSA A23.1 A23.2 : 2014 | CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE |
| ASTM C 597 : 2016 : REDLINE | Standard Test Method for Pulse Velocity Through Concrete |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.