ASTM C 1325 : 2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units
Hardcopy , PDF
10-19-2023
English
07-04-2022
Committee |
C 17
|
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers non-asbestos fiber-mat reinforced cementitious backer units manufactured to be dimensionally stable and suitable as either an unfinished substrate (see Note 1) or as a substrate for decoration such as natural stone or tile on walls, floors, or decks in wet and dry areas. It is also suitable to be used as a substrate in the Application of Class PB Exterior Insulation Finish Systems (Practice C1397), the Application of Direct-Applied Finish Systems (Practice C1516), and the Application of Exterior Insulation Finish Systems Class PI (Practice C1535).
Note 1:When used as an unfinished substrate, consult the manufacturer's written installation literature for proper application details.
1.2This specification is not applicable to asbestos-cement flat sheets (Specification C220); non-asbestos fiber cement flat sheets for exterior applications such as claddings, facades, curtain walls, and soffits (Specification C1186); gypsum backing board, coreboard, and shaftliner (Specification C1396/C1396M); water-resistant gypsum backing board (Specification C1396/C1396M); glass mat gypsum backing board (Specification C1178/C1178M); particle boards (Definitions D1554); and discrete non-asbestos fiber cement interior substrate sheets (Specification C1288).
1.3Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1922 : 2023 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters by Way of Water Loss |
ASTM C 1516 : 2005 : R2023 | Standard Practice for Application of Direct-Applied Exterior Finish Systems |
ASTM E 3355 : 2023 | Standard Guide for Characterization of Coal Combustion Products (CCPs) in Storage Area(s) for Beneficial Use |
ASTM C 1535 : 2005 : R2023 | Standard Practice for Application of Exterior Insulation and Finish Systems Class PI |
ASTM C 1780 : 2023 : REV A | Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer |
ASTM C 1186 : 2022 | Standard Specification for Flat Fiber-Cement Sheets |
ASTM C 1732 : 2019 | Standard Practice for Installation of Concrete Floor Tiles |
ASTM C 1516 : 2005 : R2017 | Standard Practice for Application of Direct-Applied Exterior Finish Systems |
ASTM C 1185 : 2008 : R2016 | Standard Test Methods for Sampling and Testing Non-Asbestos Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards |
ASTM C 1397 : 2013 : R2019 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage |
ASTM C 1288 : 2017 | Standard Specification for Fiber-Cement Interior Substrate Sheets |
ASTM C 1535 : 2005 : R2017 | Standard Practice for Application of Exterior Insulation and Finish Systems Class PI |
ASTM C 1780 : 2020 | Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer |
ASTM C 1516 : 2005 : R2023 | Standard Practice for Application of Direct-Applied Exterior Finish Systems |
ASTM C 947 : 2003 : R2023 | Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading) |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 1554 : 2010 : R2023 | Standard Terminology Relating to Wood-Base Fiber and Particle Panel Materials |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM C 1154 : 2023 | Standard Terminology for Non-Asbestos Fiber-Reinforced Cement Products |
ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM G 22 : 1976 : R1996 | Standard Practice for Determining Resistance of Plastics to Bacteria (Withdrawn 2002) |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 1554 : 2010 : R2016 | Standard Terminology Relating to Wood-Base Fiber and Particle Panel Materials |
ASTM C 1535 : 2005 : R2023 | Standard Practice for Application of Exterior Insulation and Finish Systems Class PI |
ASTM G 22 : 2023 | Standard Practice for Determining Resistance of Plastics to Bacteria |
ASTM C 666/C666M : 2015 | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024) |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM C 1154 : 2006 : R2016 | Standard Terminology for Non-Asbestos Fiber-Reinforced Cement Products |
ASTM C 947 : 2003 : R2016 | Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading) |
ASTM D 2394 : 2017 | Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring |
ASTM D 2394 : 2017 : R2022 | Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.