ASTM C 1193 : 2005 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Use of Joint Sealants
Hardcopy , PDF
11-11-2014
English
05-01-2005
Committee |
C 24
|
DocumentType |
Guide
|
Pages |
32
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.
1.2 An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C 834, C 920, or C 1311.
1.3 This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C 1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C 1249 should be consulted for this information.
1.4 Practice C 919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.
1.5 This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others. Guide C 1299 should be consulted for information on generally accepted comparative values for the characteristics and properties of the more common generic types of liquid-applied sealant.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.
1.7 The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.9 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.
ASTM C 1311 : 2014 | Standard Specification for Solvent Release Sealants |
ASTM C 1242 : 2019 | Standard Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems |
ASTM C 919 : 2019 | Standard Practice for Use of Sealants in Acoustical Applications |
ASTM C 1736 : 2011 | Standard Practice for Non-Destructive Evaluation of Adhesion of Installed Weatherproofing Sealant Joints Using a Rolling Device (Withdrawn 2020) |
ASTM C 1127/C1127M : 2015 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface |
ASTM C 1521 : 2013 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 834 : 2017 | Standard Specification for Latex Sealants |
ASTM C 1564 : 2015 | Standard Guide for Use of Silicone Sealants for Protective Glazing Systems |
ASTM E 2112 : 2019 : REV B | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
ASTM C 1253 : 2014 : R2019 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM C 1401 : 2014 | Standard Guide for Structural Sealant Glazing |
ASTM C 981 : 2005 : R2013 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1481 : 2012 : R2017 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 898/C898M : 2009 : R2017 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course |
ASTM E 2435 : 2005 : R2015 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ASTM C 920 : 2018 | Standard Specification for Elastomeric Joint Sealants |
ASTM C 717 : 2019 | Standard Terminology of Building Seals and Sealants |
ASTM E 2266 : 2011 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.