ASTM C 1012/C1012M : 2018 : REV B
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
Hardcopy , PDF
04-08-2024
English
01-09-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of length change of mortar bars immersed in a sulfate solution.
| Committee |
C 01
|
| DocumentType |
Test Method
|
| Pages |
9
|
| ProductNote |
THIS STANDARD ALSO REFERS TO ACI C201-2R-01.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of length change of mortar bars immersed in a sulfate solution. Mortar bars made using mortar described in Test Method C109/C109M are cured until they attain a compressive strength of 20.0 ± 1.0 MPa [3000 ± 150 psi], as measured using cubes made of the same mortar, before the bars are immersed.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1904 : 2022 | Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products |
| ASTM C 1894 : 2022 | Standard Guide for Microbially Induced Corrosion of Concrete Products |
| ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ASTM C 183/C183M : 2023 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
| ASTM C 1600/C1600M : 2023 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 989/C989M : 2024 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 311/C311M : 2024 | Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete |
| ASTM C 511 : 2021 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 348 : 2021 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM C 452 : 2021 | Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate |
| ASTM C 452 : 2019 : EDT 1 | Standard Test Method for Potential Expansion of Portland-Cement<brk/> Mortars Exposed to Sulfate |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 305 : 2014 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 597 : 2022 | Standard Test Method for Ultrasonic Pulse Velocity Through Concrete |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM C 1157/C1157M : 2023 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM C 597 : 2016 | Standard Test Method for Pulse Velocity Through Concrete |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 618 : 2023 : EDT 1 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM C 215 : 2019 | Standard Test Method for Fundamental Transverse, Longitudinal, and<brk/> Torsional Resonant Frequencies of Concrete Specimens |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM C 1157/C1157M : 2020 | Standard Performance Specification for Hydraulic Cement |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM C 109/C109M : 2020 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 511 : 2019 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 109/C109M : 2023 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50mm [2 in.] Cube Specimens) |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 778 : 2017 | Standard Specification for Standard Sand |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM C 618 : 2022 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM C 490/C490M : 2017 | Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete |
| ASTM C 618 : 2023 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 18 : 2019 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM C 114 : 2023 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 114 : 2009 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 348 : 2020 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
| ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 989/C989M : 2024 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 618 : 2019 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM C 215 : 1997 : EDT 1 | Standard Test Method for Fundamental Transverse, Longitudinal, and Torsional Frequencies of Concrete Specimens |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
| ASTM C 349 : 1997 | Standard Test Method for Compressive Strength of Hydraulic-Cement Mortars (Using Portions of Prisms Broken in Flexure) |
| ASTM C 490/C490M : 2021 | Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete |
| ASTM C 989/C989M : 2022 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM C 114 : 2018 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 114 : 2022 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 778 : 2021 | Standard Specification for Standard Sand |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.