ASTM B 962 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle
Hardcopy , PDF
10-18-2023
English
05-11-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This standard describes a method for measuring the density of powder metallurgy products that usually have surface-connected porosity.
| Committee |
B 09
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This standard describes a method for measuring the density of powder metallurgy products that usually have surface-connected porosity.
1.2The density of impermeable PM materials, those materials that do not gain mass when immersed in water, may be determined using Test Method B311.
1.3The current method is applicable to green compacts, sintered parts, and green and sintered test specimens.
1.4With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm3) and gram (g) units is the long-standing industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 904 : 2020 | Standard Specification for 50 Nickel-50 Iron Powder Metallurgy Soft Magnetic Parts |
| ASTM B 925 : 2015 : R2022 | Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens |
| ASTM B 610 : 2023 | Standard Test Method for Measuring Dimensional Changes Associated with Processing Metal Powders Intended for Die Compaction |
| ASTM B 331 : 2020 | Standard Test Method for Compressibility of Metal Powders in Uniaxial Compaction |
| ASTM B 595 : 2021 | Standard Specification for Materials for Aluminum Powder Metallurgy (PM) Structural Parts |
| ASTM B 823 : 2020 | Standard Specification for Materials for Copper Base Powder Metallurgy (PM) Structural Parts |
| ASTM B 883 : 2019 | Standard Specification for Metal Injection Molded (MIM) Materials |
| ASTM A 839 : 2015 : R2023 | Standard Specification for Iron-Phosphorus Powder Metallurgy Parts for Soft Magnetic Applications |
| ASTM B 438 : 2021 | Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
| ASTM B 783 : 2019 | Standard Specification for Materials for Ferrous Powder Metallurgy (PM) Structural Parts |
| ASTM F 3637 : 2023 | Standard Guide for Additive Manufacturing of Metal — Finished Part Properties — Methods for Relative Density Measurement |
| ASTM B 988 : 2018 : R2022 | Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components |
| ASTM B 312 : 2020 | Standard Test Method for Green Strength of Specimens Compacted from Metal Powders |
| ASTM B 439 : 2021 | Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
| ASTM A 811 : 2015 : R2022 | Standard Specification for Soft Magnetic Iron Parts Fabricated by Powder Metallurgy Techniques |
| ASTM B 311 : 2017 | Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity |
| ASTM B 311 : 1993 : R1997 | Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity |
| ASTM B 243 : 2022 | Standard Terminology of Powder Metallurgy |
| ASTM B 311 : 2022 | Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity |
| ASTM B 243 : 2020 | Standard Terminology of Powder Metallurgy |
| ASTM B 243 : 2023 | Standard Terminology of Powder Metallurgy |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.