ASTM B 923 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry
08-08-2020
English
10-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.05, 2017 Defines determination of skeletal density of metal powders.
| Committee |
B 09
|
| DocumentType |
Redline
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers determination of skeletal density of metal powders. The test method specifies general procedures that are applicable to many commercial pycnometry instruments. The method provides specific sample outgassing procedures for listed materials. It includes additional general outgassing instructions for other metals. The ideal gas law forms the basis for all calculations.
1.2This test method does not include all existing procedures appropriate for outgassing metal materials. The included procedures provided acceptable results for samples analyzed during an interlaboratory study. The investigator shall determine the appropriateness of listed procedures.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1State all numerical values in terms of SI units unless specific instrumentation software reports volume or density, or both, using alternative units. In this case, present both reported and equivalent SI units in the final written report. Many instruments report skeletal density as g/cm3 instead of using correct SI units (kg/m3).
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 2886 : 2017 : REDLINE | Standard Specification for Metal Injection Molded Cobalt-28Chromium-6Molybdenum Components for Surgical Implant Applications |
| NBR 15628-8 : 2013 | IMPLANTS FOR SURGERY - METALLIC COMPONENTS - PART 8: SPECIFICATION FOR METAL INJECTION MOLDED UNALLOYED TITANIUM |
| ASTM F 2885 : 2017 : REDLINE | Standard Specification for Metal Injection Molded Titanium-6Aluminum-4Vanadium Components for Surgical Implant Applications |
| ASTM C 750 : 2009 : R2014 | Standard Specification for Nuclear-Grade Boron Carbide Powder |
| ASTM B 988 : 2013 | Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components |
| ASTM F 3049 : 2014 | Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes |
| NASA MSFC SPEC 3706 : 2016 | SPECIFICATION FOR 60NI-40TI BILLETS |
| ASTM F 2989 : 2013 : REDLINE | Standard Specification for Metal Injection Molded Unalloyed Titanium Components for Surgical Implant Applications |
| SAE AMS 7001 : 2018 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, POWDER FOR ADDITIVE MANUFACTURING, 62NI - 21.5CR - 9.0MO - 3.65NB |
| ASTM C 750 : 2009 | Standard Specification for Nuclear-Grade Boron Carbide Powder |
| ASTM B 215 : 2015 : REDLINE | Standard Practices for Sampling Metal Powders |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.