ASTM B 90/B90M : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Magnesium-Alloy Sheet and Plate
07-02-2021
English
12-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.02, 2016 Specifies magnesium alloys in sheet and plate form designated.
| Committee |
B 07
|
| DocumentType |
Redline
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers magnesium alloys in sheet and plate form designated as shown in Table 1.
1.2The values stated in either inch-pound or SI units are to be regarded separately as standards. The SI units are shown in brackets or in separate tables or columns. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-PRF-46002 Revision D:2010 | PRESERVATIVE OIL, CONTACT AND VOLATILE CORROSION-INHIBITED |
| MIL-DTL-32333 Base Document:2009 | ARMOR PLATE, MAGNESIUM ALLOY, AZ31B, APPLIQUE |
| SAE ARP 6256 : 2014 | MAGNESIUM ALLOYS IN AIRCRAFT SEATS - ENGINEERING DESIGN AND FABRICATION RECOMMENDED PRACTICES |
| ASTM B 951 : 2011 | Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought |
| ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
| ASTM B 881 : 2017 : REDLINE | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM B 557 : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| FED-STD-184 Revision B:1977 | IDENTIFICATION MARKING OF ALUMINUM, MAGNESIUM, AND TITANIUM |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| ASTM B 557M : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| SAE AMS M 3171 : 1998 | MAGNESIUM ALLOY, PROCESSES FOR PRETREATMENT AND PREVENTION OF CORROSION ON |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM B 954 : 2015 : REDLINE | Standard Test Method for Analysis of Magnesium and Magnesium Alloys by Atomic Emission Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.