ASTM B 851 : 2004 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or Chromium Plating, or as Final Finish
Hardcopy , PDF
12-04-2020
English
11-24-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.05, 2017 Describes the requirements for automated, controlled shot peening of metallic articles prior to electrolytic or autocatalytic deposition of nickel or chromium, or as a final finish, using shot made of cast steel, conditioned cut wire, or ceramic media.
| Committee |
B 08
|
| DocumentType |
Standard
|
| Pages |
9
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the requirements for automated, controlled shot peening of metallic articles prior to electrolytic or autocatalytic deposition of nickel or chromium, or as a final finish, using shot made of cast steel, conditioned cut wire, or ceramic media. The process is applicable to those materials on which test work has shown it to be beneficial within given intensity ranges. It is not suitable for brittle materials. Hand peening and rotary flap peening are excluded specifically.
1.2Shot peening induces residual compressive stresses in the surface and near-surface layers of metallic articles, controlling or limiting the reduction in fatigue properties that occurs from nickel or chromium plating of the article, or the fatigue properties of unplated articles.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM B 733 : 2015 : REDLINE | Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal |
| SAE J 1830 : 2013 | SIZE CLASSIFICATION AND CHARACTERISTICS OF CERAMIC SHOT FOR PEENING |
| MIL-STD-45662 Revision A:1988 | CALIBRATION SYSTEMS REQUIREMENTS |
| SAE J 827 : 2013 | HIGH-CARBON CAST-STEEL-SHOT |
| MIL S 13165 : C | SHOT PEENING OF METAL PARTS |
| QQ-C-320 Revision B:1974 | CHROMIUM PLATING (ELECTRODEPOSITED) |
| ASTM B 607 : 2015 : REDLINE | Standard Specification for Autocatalytic Nickel Boron Coatings for Engineering Use |
| SAE J 441 : 2013 | Cut Wire Shot |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| MIL C 26074 : E | COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ASTM B 320 : 1960 : R2019 | Standard Practice for Preparation of Iron Castings for Electroplating |
| ASTM B 656 : 1991 | Standard Guide for Autocatalytic (Electroless) Nickel-Phosphorus Deposition on Metals for Engineering Use (Withdrawn 2000) |
| QQ-N-290 Revision A:1971 | NICKEL PLATING (ELECTRODEPOSITED) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.