ASTM B 69 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Rolled Zinc
10-15-2020
English
10-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.04, 2016 Specifies two types of commercial rolled zinc.
| Committee |
B 02
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers two types of commercial rolled zinc as described in 1.2. It should be understood that the specification is general. Any closer limitations on permissible variations shall be a matter of agreement between the supplier (manufacturer) and the purchaser.
1.2Rolled zinc is furnished in two types as follows:
1.2.1Type I—Coils or sheets cut from strip (ribbon) rolled zinc and
1.2.2Type II—Coils or sheets cut from strip (ribbon) rolled zinc.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
| NACE 01105 : 0 | SACRIFICIAL CATHODIC PROTECTION OF REINFORCED CONCRETE ELEMENTS - A STATE-OF-THE-ART-REPORT |
| MIL-C-40084 Revision C:1990 | CORROSION PREVENTIVE COMPOUND, WATER EMULSIFIABLE, OIL TYPE |
| MIL-DTL-21567 Revision B:2009 | COMPOUND, SILICONE, SOFT FILM |
| ASTM C 1861 : 2017 | Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster |
| MIL-STD-186 Revision F:2002 | PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS |
| SAE J 1837 : 2017 | ELECTROPLATE REQUIREMENTS FOR DECORATIVE CHROMIUM DEPOSITS ON ZINC BASE MATERIALS USED FOR EXTERIOR ORNAMENTATION |
| MIL-HDBK-270 Revision A:1991 | METALLIC MATERIALS FOR LOW MAGNETIC APPLICATIONS, MAGNETIC PERMEABILITY AND ELECTRICAL CONDUCTIVITY, CHARACTERISTICS OF (METRIC) |
| MIL-A-52818 Base Document:1974 | ANCHOR, GUY: SHIELD, EXPANSION |
| ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
| ANSI/EIMA 99A : 2001 | EXTERIOR INSULATION AND FINISH SYSTEMS (EIFS) |
| SAE AMS 8660 : 2018 | SILICONE COMPOUND NATO CODE NUMBER S-736 |
| ASTM E 634 : 2012-05 | PRACTICE FOR SAMPLING OF ZINC AND ZINC ALLOYS BY SPARK ATOMIC EMISSION SPECTROMETRY |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM E 536 : 2016 : REDLINE | Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys |
| ISO 3815-1:2005 | Zinc and zinc alloys — Part 1: Analysis of solid samples by optical emission spectrometry |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
| ISO 3815-2:2005 | Zinc and zinc alloys — Part 2: Analysis by inductively coupled plasma optical emission spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.