ASTM B 557 : 2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
Available format(s)
Hardcopy , PDF
Superseded date
11-08-2023
Superseded by
Language(s)
English
Published date
10-29-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2and are derived from Test MethodsE8, which cover the tension testing of all metallic materials.
| Committee |
B 07
|
| DocumentType |
Test Method
|
| Pages |
16
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8, which cover the tension testing of all metallic materials.
1.2The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:Foil is sheet metal less than 0.0079 in. thick. There is an overlap in the thickness range 0.006 to 0.0079 in. defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material.
Note 2:A complete metric companion to Test Methods B557 has been developed—Test Methods B557M; therefore, no metric equivalents are presented in these test methods.
| ASTM B 609/B609M : 2012 : R2021 | Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes |
| ASTM B 941 : 2022 | Standard Specification for Heat Resistant Aluminum-Zirconium Alloy Wire for Electrical Purposes |
| ASTM B 210/B210M : 2019 : REV A | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes |
| ASTM B 199 : 2017 | Standard Specification for Magnesium-Alloy Permanent Mold Castings |
| ASTM B 491/B491M : 2015 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| ASTM B 398/B398M : 2022 | Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes |
| ASTM B 646 : 2019 | Standard Practice for Fracture Toughness Testing of Aluminum Alloys |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 108/B108M : 2019 | Standard Specification for Aluminum-Alloy Permanent Mold Castings |
| ASTM B 247 : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
| ASTM B 947 : 2014 : R2020 : EDT 1 | Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate |
| ASTM E 1592 : 2005 : R2017 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
| ASTM B 807/B807M : 2020 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| ASTM B 483/B483M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM B 800 : 2005 : R2021 | Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes—Annealed and Intermediate Tempers |
| ASTM B 26/B26M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Sand Castings |
| ASTM B 94 : 2018 | Standard Specification for Magnesium-Alloy Die Castings |
| ASTM E 9 : 2019 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
| ASTM B 316/B316M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| ASTM B 928/B928M : 2015 | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| ASTM B 221 : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM B 1013 : 2022 | Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings |
| ASTM G 129 : 2021 | Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking |
| ASTM B 90/B90M : 2021 | Standard Specification for Magnesium-Alloy Sheet and Plate |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM B 91 : 2017 | Standard Specification for Magnesium-Alloy Forgings |
| ASTM B 230/B230M : 2022 | Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes |
| ASTM B 80 : 2015 | Standard Specification for Magnesium-Alloy Sand Castings |
| ASTM B 107/B107M : 2013 : R2021 | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM B 241/B241M : 2022 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| ASTM B 969/B969M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, and the Semi-Solid Thixocast and Rheocast Casting Processes |
| ASTM B 86 : 2022 | Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings |
| ASTM B 308/B308M : 2020 | Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles |
| ASTM B 955/B955M : 2018 | Standard Specification for Aluminum-Alloy Centrifugal Castings |
| ASTM B 918/B918M : 2020 : REV A | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
| ASTM B 233 : 1997 : R2021 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 618/B618M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Investment Castings |
| ASTM B 661 : 2012 : R2020 | Standard Practice for Heat Treatment of Magnesium Alloys |
| ASTM B 403 : 2020 | Standard Specification for Magnesium-Alloy Investment Castings |
| ASTM B 429/B429M : 2020 | Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube |
| ASTM B 324 : 2001 : R2021 | Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 211/B211M : 2019 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM B 686/B686M : 2018 | Standard Specification for Aluminum Alloy Castings, High-Strength |
| ASTM B 945 : 2021 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers |
| ASTM B 917/B917M : 2012 : R2020 | Standard Practice for Heat Treatment of Aluminum-Alloy Castings From All Processes |
| ASTM C 1671 : 2020 : REV A | Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging |
| ASTM B 234 : 2017 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| ASTM F 3122 : 2014 : R2022 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| ASTM B 209/B209M : 2021 : REV A | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM E 83 : 2023 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 1012 : 2014 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 2000 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 83 : 2016 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM B 209 : 2014 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 1998 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 6 : 2002 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1012 : 1999 | Standard Practice for Verification of Specimen Alignment Under Tensile Loading |
| ASTM E 1012 : 2012 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 1012 : 2014 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1012 : 2012 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2023 : REV A | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 1012 : 2005 | Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2015 : EDT 4 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 6 : 2023 | Standard Terminology Relating to Methods of Mechanical Testing |
| ASTM E 1012 : 2019 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.