ASTM B 49 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Copper Rod for Electrical Purposes
08-10-2020
English
04-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.01, 2017 Defines the requirements for rod in diameters from [1/4] to 1[3/8] in. (6.4 to 35 mm) produced from high conductivity coppers, namely, electrolytic tough-pitch, oxygen-free, or fire-refined high conductivity coppers, and are suitable for further fabrication into electrical conductors.
| Committee |
B 05
|
| DocumentType |
Redline
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers the requirements for rod in diameters from 1/4to 13/8in. (6.4 to 35 mm) produced from high conductivity coppers listed in Table 1, namely, electrolytic tough-pitch, oxygen-free, or fire-refined high conductivity coppers, and are suitable for further fabrication into electrical conductors.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The following safety hazards caveat pertains only to Section 13. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Standards | Relationship |
| UNE 37144:1977 | Identical |
| ASTM B 115 : 2010 : R2016 | Standard Specification for Electrolytic Copper Cathode |
| ASTM B 965 : 2009 | Standard Specification for High Performance Tin-Coated Annealed Copper Wire Intended for Electrical and Electronic Application for Solderability |
| ASTM B 973 : 2010 : R2014 | Standard Specification for Tin-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application |
| ASTM B 33 : 2010 : R2014 | Standard Specification for Tin-Coated Soft or Annealed Copper Wire for Electrical Purposes |
| ASTM B 47 : 1995 : REV A : R2001 | Standard Specification for Copper Trolley Wire |
| ASTM B 298 : 2012 : R2017 | Standard Specification for Silver-Coated Soft or Annealed Copper Wire |
| ASTM B 116 : 1995 | Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage |
| IEEE 837-2014 | IEEE Standard for Qualifying Permanent Connections Used in Substation Grounding |
| ASTM B 47 : 1995 : REV A : R2017 | Standard Specification for Copper Trolley Wire |
| ASTM B 971 : 2010 | Standard Specification for Silver-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application |
| MIL-DTL-2726 Revision C:2006 | Receptacle, Receptacle Plugs, Switch and Receptacles, and Outlets (Electrical), General Specification for |
| ASTM B 972 : 2010 : R2014 | Standard Specification for Nickel-Coated Braid and Ribbon Flat Copper Wire Intended for use in Electronic Application |
| ASTM B 48 : 2000 : R2011 | Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors |
| ASTM B 298 : 2012 | Standard Specification for Silver-Coated Soft or Annealed Copper Wire |
| ASTM B 1001 : 2017 | Standard Specification for Copper Electrode Wire Used for Welding Seams of Steel Cans |
| ASTM B 47 : 1995 : REV A : R2007 | Standard Specification for Copper Trolley Wire |
| ASTM B 33 : 2010 | Standard Specification for Tin-Coated Soft or Annealed Copper Wire for Electrical Purposes |
| ASTM B 47 : 1995 : REV A | Standard Specification for Copper Trolley Wire |
| ASTM B 115 : 2010 | Standard Specification for Electrolytic Copper Cathode |
| ASTM B 965 : 2009 : R2014 | Standard Specification for High Performance Tin-Coated Annealed Copper Wire Intended for Electrical and Electronic Application for Solderability |
| ASTM B 189 : 2005 : R2015 | Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes |
| ASTM B 355 : 2011 | Standard Specification for Nickel-Coated Soft or Annealed Copper Wire |
| ASTM B 116 : 1995 : R2017 | Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolley Wire for Industrial Haulage |
| ASTM B 48 : 2000 : R2005 : EDT 1 | Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors |
| ASTM B 48:2000 | Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors |
| ASTM B 973:2010 | Standard Specification for Tin-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application |
| ASTM B 47 : 1995 : REV A : R2012 | Standard Specification for Copper Trolley Wire |
| ASTM B 48 : 2000 : R2016 | Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors |
| ASTM B 189 : 2005 : R2010 | Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes |
| ASTM B 972 : 2010 | Standard Specification for Nickel-Coated Braid and Ribbon Flat Copper Wire Intended for use in Electronic Application |
| ASTM B 116 : 1995 : R2007 | Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage |
| ASTM B 355 : 2011 : R2016 | Standard Specification for Nickel-Coated Soft or Annealed Copper Wire |
| QQ-W-343 Revision G:1997 | WIRE, ELECTRICAL, COPPER (UNINSULATED) |
| ASTM B 971 : 2010 : R2014 | Standard Specification for Silver-Coated Braid and Ribbon Flat Copper Wire intended for use in Electronic Application |
| A-A-59551 Revision A:2009 | WIRE, ELECTRICAL, COPPER (UNINSULATED) |
| ASTM B 246 : 2015 : REDLINE | Standard Specification for Tinned Hard-Drawn and Medium-Hard-Drawn Copper Wire for Electrical Purposes |
| ASTM B 189 : 2005 | Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes |
| ASTM B 116 : 1995 : R2001 | Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage |
| ASTM B 116 : 1995 : R2012 | Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage |
| ASTM B 224 : 2016 : REDLINE | Standard Classification of Coppers |
| ASTM E 2575 : 2008 | Standard Test Method for Determination of Oxygen in Copper and Copper Alloys (Withdrawn 2017) |
| ASTM B 846 : 2011-07 | TERMINOLOGY FOR COPPER AND COPPER ALLOYS |
| ASTM B 5 : 2016 : REDLINE | Standard Specification for High Conductivity Tough-Pitch Copper Refinery Shapes |
| ASTM E 1606 : 2015 : REDLINE | Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Aluminum Redraw Rod for Electrical Purposes |
| ASTM B 193 : 2016 : REDLINE | Standard Test Method for Resistivity of Electrical Conductor Materials |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.