ASTM B 232/B232M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)
01-30-2023
English
09-18-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.03, 2017 Specifies concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) wires and round, coated steel core wire for use as overhead electrical conductors.
| Committee |
B 01
|
| DevelopmentNote |
Supersedes ASTM B 232 and ASTM B 232M (06/2001)
|
| DocumentType |
Redline
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) wires and round, coated steel core wire(s) for use as overhead electrical conductors (Explanatory Note 1 and Explanatory Note 2).
1.2ACSR covered by this specification has nine types of coated steel core wire which are designated by abbreviations as follows (Explanatory Note 2):
1.2.1ACSR/GA or ACSR/GA2—ACSR using Class A zinc-coated steel wire,
1.2.2ACSR/GC or ACSR/GC2—ACSR using Class C zinc-coated steel wire,
1.2.3ACSR/MA or ACSR/MA2—ACSR using Class A Zn-5A1-MM coated steel wire,
1.2.4ACSR/HS or ACSR/GA3—ACSR using Class A zinc-coated high-strength steel wires,
1.2.5ACSR/MS or ACSR/MA3—ACSR using Class A Zn-5A1-MM coated high-strength steel wires,
1.2.6ACSR/GA4—ACSR using Class A zinc-coated extra-high-strength steel wires,
1.2.7ACSR/MA4—ACSR using Class A Zn-5A1-MM coated extra-high-strength steel wires,
1.2.8ACSR/GA5—ACSR using Class A zinc-coated ultra-high-strength steel wires,
1.2.9ACSR/MA5—ACSR using Class A Zn-5Al-MM coated ultra-high-strength steel wires.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM B 401 : 2012 | Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/COMP) |
| ASTM B 779 : 2018 : REDLINE | Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/TW) |
| ASTM B 911/B911M : 2012 : R2016 | Standard Specification for ACSR Twisted Pair Conductor (ACSR/TP) |
| ASTM B 701/B701M : 2013 | Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD) |
| ASTM B 1006 : 2017 | Standard Specification for Electrical Overhead Conductor Code Word Names |
| ASTM B 401 : 2012 : R2016 | Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/COMP) |
| CSA C22.3 No. 1 : 2010 : INC : UPD 1 : 2011 : R2015 | OVERHEAD SYSTEMS |
| ASTM B 911/B911M : 2012 | Standard Specification for ACSR Twisted Pair Conductor (ACSR/TP) |
| CSA C22.3 No. 1 : 2010 | OVERHEAD SYSTEMS |
| ASTM B 701/B701M : 2013 : R2018 | Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD) |
| ANSI H35.1M : 2004 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM (METRIC) |
| ASTM B 958 : 2008 | Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc<span class='unicode'>–</span>5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors |
| ASTM B 957 : 2008 | Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead Electrical Conductors |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ANSI H35.1 : 2006 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.