ASTM B 209/B209M : 2021 : REV A
Current
The latest, up-to-date edition.
Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
Hardcopy , PDF
English
12-01-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
B 07
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2, 3, 4, and 5, and in the following finishes:
1.1.1Plate in all alloys and sheet in heat-treatable alloys: mill finish.
1.1.2Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish.
1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
Note 1:Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2:See Specification B632/B632M for tread plate.
Note 3:See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 683 : 2021 | Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery |
| ASTM E 1800 : 2021 | Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (160 °F Elevated Humidity Service), Type I Panels |
| ASTM D 8379/D8379M : 2021 | Standard Practice for Evaluating Nighttime Retroreflective Sheeting Effectiveness Using Positive-Contrast Textual Sign Scenario Performance Analysis |
| ASTM D 1669/D1669M : 2007 : R2023 | Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings |
| ASTM F 1178 : 2011 : R2022 | Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture |
| ASTM F 683 : 2023 : REV A | Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery |
| ASTM F 1070 : 2019 : R2024 | Standard Specification for Doors, Non-Tight, for Marine Use |
| ASTM B 253 : 2011 : R2022 | Standard Guide for Preparation of Aluminum Alloys for Electroplating |
| ASTM E 1826 : 2023 | Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels |
| ASTM F 1333 : 1991 : R2024 | Standard Specification for Construction of Fire and Foam Station Cabinets |
| ASTM F 1069 : 2019 : R2024 | Standard Specification for Doors, Watertight, Gastight/Airtight and Weathertight, Individually Dogged, for Marine Use |
| ASTM C 1936 : 2023 | Standard Test Method for Corrosiveness of Mineral-Fiber or Cellulosic-Fiber Insulation by Comparison to Control |
| ASTM F 640 : 2023 | Standard Test Methods for Determining Radiopacity for Medical Use |
| ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM B 746/B746M : 2024 : REV A | Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM D 8514/D8514M : 2023 | Standard Specification for Flexible, Retroreflective Sheeting for Use in High Visibility Vehicle Markings |
| ASTM B 1021 : 2021 | Standard Test Method for Peel Resistance of Metal Sheets Joined by High Strength Bonds |
| ASTM E 3110/E3110M : 2022 | Standard Test Method for Collection of Ballistic Limit Data for Ballistic-resistant Torso Body Armor and Shoot Packs |
| ASTM B 985 : 2024 | Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis |
| ASTM B 632/B632M : 2024 | Standard Specification for Aluminum-Alloy Rolled Tread Plate |
| ASTM E 1004 : 2023 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
| ASTM B 928/B928M : 2015 | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| ASTM B 557 : 2015 : R2023 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM B 557M : 2015 : R2023 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| ASTM G 47 : 2020 | Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM G 47 : 2022 | Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products |
| ASTM E 716 : 2016 : R2021 : EDT 2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 660 : 2021 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM B 557 : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM G 34 : 2001 : R2018 : EDT 1 | Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) |
| ASTM B 928/B928M : 2015 : R2023 | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| ASTM E 1004 : 2017 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
| ASTM B 928/B928M : 2015 : R2023 : EDT 1 | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| ASTM B 632/B632M : 2018 | Standard Specification for Aluminum-Alloy Rolled Tread Plate |
| ASTM B 660 : 2023 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM B 548 : 2003 : R2017 | Standard Test Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels |
| ASTM E 290 : 2022 | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM G 34 : 2023 | Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) |
| ASTM B 557M : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| ASTM E 716 : 2016 : R2021 : EDT 1 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 985 : 2012 : R2016 | Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis |
| ASTM E 290 : 2014 | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.