ASTM B 159/B159M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Phosphor Bronze Wire
Hardcopy , PDF
07-29-2024
English
10-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
B 05
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification establishes the requirements for round and flat (square and rectangular) phosphor bronze wire of UNS Alloy Nos. C51000, C52100, and C52400 for general and spring applications.
1.1.1Rectangular and square wire of the three alloys are generally available in sizes up to a maximum of 0.188 in. [5 mm] thick and 1.250 in. [32 mm] wide.
1.1.2Round wire from Copper Alloy UNS No. C51000 is generally available in sizes up to 0.500 in. [13 mm] in diameter.
1.2Units—The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.
1.3Additional requirements for these products are established in Specification B250/B250M, see Section 3.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:It is to be understood that this specification is general. Since the product is used for many applications where the requirements of the operations used are too particular to be specified by any of the ordinary mechanical tests, it is frequently advisable to submit samples or drawings to the manufacturer and secure an adjustment of temper to suit the actual application for which the product is intended.
Note 2:Product in rod, bar and shape form is produced to Specification B139/B139M.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 1974 : 2023 | Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe |
| ASTM B 250/B250M : 2019 | Standard Specification for General Requirements for Wrought Copper Alloy Wire |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM B 950 : 2023 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM B 950 : 2021 : EDT 1 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 478 : 2008 : R2017 | Standard Test Methods for Chemical Analysis of Copper Alloys |
| ASTM E 290 : 2022 | Standard Test Methods for Bend Testing of Material for Ductility |
| ASTM B 950 : 2021 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM B 950 : 2022 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM E 290 : 2014 | Standard Test Methods for Bend Testing of Material for Ductility |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.