ASTM B 154 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Mercurous Nitrate Test for Copper Alloys
Hardcopy , PDF
06-20-2022
English
11-29-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
B 05
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method describes the technique for conducting the mercurous nitrate test for residual stresses in wrought copper alloy mill products.
Note 1:For any particular copper alloy, reference should be made to the material specification.
Note 2:Test Method B858 may be considered as a possible alternative test method which does not involve the use of mercury.
Note 3:This test method is considered historically reliable for determining the potential state of residual stress in copper alloys, but not promoted for use due to the hazards relating to mercury use and environmentally appropriate disposal.
1.2Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determines the applicability of regulatory limitations prior to use. For specific precautionary and hazard statements see Sections 1, 6, and 7. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.)
| ASTM B 552 : 2019 | Standard Specification for Seamless and Welded Copper–Nickel Tubes for Water Desalting Plants |
| ASTM F 467M : 2006 : REV A : R2018 | Standard Specification for Nonferrous Nuts for General Use (Metric) |
| ASTM B 395/B395M : 2018 | Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes |
| ASTM B 150/B150M : 2019 | Standard Specification for Aluminum Bronze Rod, Bar, and Shapes |
| ASTM B 587 : 2019 | Standard Specification for Welded Brass Tube |
| ASTM F 468M : 2006 : R2018 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric) |
| ASTM B 138/B138M : 2011 : R2017 | Standard Specification for Manganese Bronze Rod, Bar, and Shapes |
| ASTM B 359/B359M : 2018 | Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins |
| ASTM B 371/B371M : 2019 | Standard Specification for Copper-Zinc-Silicon Alloy Rod |
| ASTM B 956 : 2019 : EDT 1 | Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins |
| ASTM B 21/B21M : 2020 | Standard Specification for Naval Brass Rod, Bar, and Shapes |
| ASTM B 19 : 2020 | Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks |
| ASTM B 111/B111M : 2018 : REV A | Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
| ASTM B 251/B251M : 2017 | Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube |
| ASTM B 858 : 2006 : R2018 | Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys |
| ASTM B 135/B135M : 2017 | Standard Specification for Seamless Brass Tube |
| ASTM F 468 : 2016 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use |
| ASTM B 43 : 2020 | Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
| ASTM B 249/B249M : 2020 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
| ASTM F 3042 : 2013 : R2018 | Standard Specification for Nonferrous Hex Socket, Slotted Headless, and Square Head Set Screws |
| ASTM B 1014 : 2020 | Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s) |
| ASTM B 543/B543M : 2018 | Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube |
| ASTM B 950 : 2021 : EDT 1 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM F 467 : 2013 : R2018 | Standard Specification for Nonferrous Nuts for General Use |
| ASTM F 1387 : 2019 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.