ASTM A 563/A563M : 2021 : REV A : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric)
Hardcopy , PDF
01-09-2024
English
03-24-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 16
|
| DocumentType |
Standard
|
| Pages |
12
|
| ProductNote |
NOTE—Table 2 was editorially corrected in March 2022.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification2 covers chemical and mechanical requirements for eleven grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts.
Note 1:See Appendix X1 for guidance on suitable application of nut grades.
1.2The requirements for any grade of nut may, at the supplier's option, and with notice to the purchaser, be fulfilled by furnishing nuts of one of the stronger grades specified herein unless such substitution is barred in the inquiry and purchase order.
1.3Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3125/F3125M : 2021 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM B 695 : 2021 | Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
| ASTM F 1789 : 2017 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM B 746/B746M : 2022 : EDT 1 | Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM A 194/A194M : 2020 : REV A | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM F 1789 : 2022 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1941/F1941M : 2016 | Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric |
| ASTM F 3148 : 2017 : REV A | Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions |
| ASTM A 194/A194M : 2023 | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM F 3019/F3019M : 2019 | Standard Specification for Chromium Free Zinc-Flake Composite, with or without Integral Lubricant, Corrosion Protective Coatings for Fasteners |
| ASTM F 3125/F3125M : 2022 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM A 394 : 2008 : R2015 | Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare |
| ASTM F 812 : 2012 : R2017 | Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series |
| ASTM F 2329/F2329M : 2015 : R2023 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 1789 : 2017 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM A 194/A194M : 2022 | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM A 194/A194M : 2022 : REV A | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM F 3125/F3125M : 2023 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM A 307 : 2021 | Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength |
| ASTM F 1789 : 2023 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 2329/F2329M : 2015 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 3125/F3125M : 2021 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM F 812 : 2012 : R2022 | Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.