ASTM A 479/A479M : 2023 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
Hardcopy , PDF
05-10-2024
English
06-09-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2
Note 1:There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 580/A580M : 2023 | Standard Specification for Stainless Steel Wire |
| ASTM F 1376 : 1992 : R2020 | Standard Guide for Metallurgical Analysis for Gas Distribution System Components (Withdrawn 2023) |
| ASTM F 1508 : 1996 : R2021 | Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM A 1082/A1082M : 2016 : R2021 | Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications |
| ASTM C 1533 : 2015 : R2022 | Standard Guide for General Design Considerations for Hot Cell Equipment |
| ASTM A 1069/A1069M : 2019 | Standard Specification for Laser and Laser Hybrid Welded Stainless Steel Bars, Plates, and Shapes |
| ASTM B 649 : 2021 | Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N <brk/>Low-Carbon Alloy Bar and Wire, Ni-Cr-Fe-Mo-N Alloy Wire, and Ni-Fe-Cr-Mo-N Alloy Bar |
| ASTM A 182/A182M : 2023 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
| ASTM F 1387 : 2019 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM A 484/A484M : 2024 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM A 1069/A1069M : 2023 | Standard Specification for Stainless Steel Laser and Laser Hybrid Welded Bars, Plates, Sharp-Cornered Profile (SCP), and Built-up Shapes |
| ASTM A 182/A182M : 2024 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
| ASTM F 3184 : 2016 : R2023 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM A 1127/A1127M : 2023 | Standard Specification for Stainless Steel Laser and Laser-Hybrid Welded, Sharp-Cornered Profile (SCP) or Built-Up Rounded Corner Square, Rectangular, and Special Shape Structural Tube |
| ASTM F 1387 : 2023 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 484/A484M : 2024 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 484/A484M : 2023 : REV A | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.