ASTM A 203/A203M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel
07-12-2023
English
11-03-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.04, 2017 Defines nickel-alloy steel plates intended primarily for welded pressure vessels.
| Committee |
A 01
|
| DocumentType |
Redline
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification2 covers nickel-alloy steel plates intended primarily for welded pressure vessels.
1.2Plates under this specification are available with four strength levels and two nickel compositions as follows:
| Grade | Nominal Nickel | Yield Strength, min, ksi [MPa] | Tensile Strength, min, ksi [MPa] |
| A | 2.25 | 37 [255] | 65 [450] |
| B | 2.25 | 40 [275] | 70 [485] |
| D | 3.50 | 37 [255] | 65 [450] |
| E | 3.50 | 40 [275] | 70 [485] |
| F | 3.50 | ||
| 2 in. [50 mm] and under | 55 [380] | 80 [550] | |
| Over 2 in. [50 mm] | 50 [345] | 75 [515] | |
1.3The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.
1.4The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| AWS A5.28/A5.28M : 2005 : R2015 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND RODS FOR GAS SHIELDED ARC WELDING |
| BS 1560-3.1:1989 | Circular flanges for pipes, valves and fittings (Class designated). Steel, cast iron and copper alloy flanges Specification for steel flanges |
| 00/716563 DC : DRAFT NOV 2000 | EN 1759-1 - FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, CLASS DESIGNATED - PART 1: STEEL FLANGES, NPS 1/2 TO 24 |
| AWS A5.23/A5.23M : 2011 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND FLUXES FOR SUBMERGED ARC WELDING |
| DIN EN 1759-1:2005-02 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| BS EN ISO 10439:2002 | Petroleum, chemical and gas service industries. Centrifugal compressors |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| I.S. EN ISO 10439:2002 | PETROLEUM, CHEMICAL AND GAS SERVICE INDUSTRIES - CENTRIFUGAL COMPRESSORS |
| BS 4504-3.1:1989 | Circular flanges for pipes, valves and fittings (PN designated). Steel, cast iron and copper alloy flanges Specification for steel flanges |
| AWS A5.29 : 1998 | SPECIFICATION FOR LOW ALLOY STEEL ELECTRODES FOR FLUX CORED ARC WELDING |
| ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B31.3:2016 | PROCESS PIPING |
| 00/714962 DC : DRAFT OCT 2000 | PREN 12516-1 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOF STEEL VALVE SHELLS |
| AWS A5.5/A5.5M : 2014 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING |
| AWS A5.28/A5.28M : 2005 : INC : ERR 1 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND RODS FOR GAS SHIELDED ARC WELDING |
| Z245.15-17 | Steel valves |
| AWS C5.7 : 2000 | RECOMMENDED PRACTICES FOR ELECTROGAS WELDING |
| ISO 10439:2002 | Petroleum, chemical and gas service industries Centrifugal compressors |
| BS EN 1759-1:2004 | Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated Steel flanges, NPS 1/2 to 24 |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN ISO 10439:2002 | Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002) |
| NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
| ASTM A 671 : 2009 | Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures |
| AWS A5.29/A5.29M : 2010 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES FOR FLUX CORED ARC WELDING |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| ASME STS 1 : 2011 | Steel Stacks (STS-1 - 2011) |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
| ASTM A 435/A435M : 2017 : REDLINE | Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates |
| ASTM A 577/A577M : 2017 : REDLINE | Standard Specification for Ultrasonic Angle-Beam Examination of Steel Plates |
| ASTM A 578/A578M : 2017 : REDLINE | Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.