ASTM A 182/A182M : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
Hardcopy , PDF
09-28-2022
English
06-15-2021
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
17
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification2 covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications that are referenced in Section 2.
1.2For bars and products machined directly from bar or hollow bar (other than those directly addressed by this specification; see 6.4), refer to Specifications A479/A479M, A739, or A511/A511M for the similar grades available in those specifications.
1.3Products made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. For larger products and products for other applications, refer to Specifications A336/A336M and A965/A965M for the similar ferritic and austenitic grades, respectively, available in those specifications.
1.4Several grades of low alloy steels and ferritic, martensitic, austenitic, and ferritic-austenitic stainless steels are included in this specification. Selection will depend upon design and service requirements. Several of the ferritic/austenitic (duplex) grades are also found in Specification A1049/A1049M.
1.5Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.
1.6This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.7The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 721 : 2018 | Standard Specification for Gage Piping Assemblies |
ASTM F 1508 : 1996 : R2021 | Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services |
ASTM F 1565 : 2000 : R2019 | Standard Specification for Pressure-Reducing Valves for Steam Service |
ASTM F 1545 : 2015 : REV A | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
ASTM F 1155 : 2010 : R2019 | Standard Practice for Selection and Application of Piping System Materials |
ASTM F 987 : 2004 : R2017 | Standard Specification for Portable Intermediate Flush Deck Stanchion |
ASTM A 961/A961M : 2020 | Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications<?Pub _bookmark Command="[Quick Mark]"?> |
ASTM F 1387 : 2019 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM A 1049/A1049M : 2018 | Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for Pressure Vessels and Related Components |
ASTM F 1511 : 2018 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM A 961/A961M : 2021 | Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications |
ASTM F 1545 : 2015 : REV A : R2021 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
ASTM F 987 : 2004 : R2022 | Standard Specification for Portable Intermediate Flush Deck Stanchion |
ASTM A 511/A511M : 2021 | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar |
ASTM A 961/A961M : 2020 | Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications<?Pub _bookmark Command="[Quick Mark]"?> |
ASTM A 788/A788M : 2022 | Standard Specification for Steel Forgings, General Requirements |
ASTM A 484/A484M : 2021 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
ASTM A 511/A511M : 2021 : REV A | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar |
ASTM A 965/A965M : 2021 | Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts |
ASTM A 739 : 1990 : REV A : R2022 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
ASTM A 739 : 1990 : REV A : R2016 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
ASTM A 961/A961M : 2021 | Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications |
ASTM A 1084 : 2015 : REV A : R2022 | Standard Test Method for Detecting Detrimental Phases in Lean Duplex Austenitic/Ferritic Stainless Steels |
ASTM A 923 : 2014 | Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels |
ASTM A 788/A788M : 2019 : REV A | Standard Specification for Steel Forgings, General Requirements |
ASTM A 479/A479M : 2020 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 484/A484M : 2022 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
ASTM A 479/A479M : 2021 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 262 : 2015 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM A 511/A511M : 2020 | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar |
ASTM A 965/A965M : 2021 : REV A | Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts |
ASTM A 1084 : 2015 : REV A | Standard Test Method for Detecting Detrimental Phases in Lean Duplex Austenitic/Ferritic Stainless Steels |
ASTM A 923 : 2022 | Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels |
ASTM A 788/A788M : 2022 : REV A | Standard Specification for Steel Forgings, General Requirements |
ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
ASTM A 484/A484M : 2020 : REV B | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
ASTM A 763 : 2015 : R2021 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels |
ASTM A 763 : 2015 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels |
ASTM A 262 : 2015 : R2021 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.