ASTM A 1034/A1034M : 2010 : REV A : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Testing Mechanical Splices for Steel Reinforcing Bars
Hardcopy , PDF
02-01-2024
English
12-07-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.04, 2018 Defines the testing of mechanical splices for reinforcing bars.
| Committee |
A 01
|
| DevelopmentNote |
Supersedes ASTM A 1034. (05/2005)
|
| DocumentType |
Test Method
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2015
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the testing of mechanical splices for reinforcing bars. The various tests herein described can be specified in total or individually.
1.2The test methods herein described are applicable to any type of mechanical splice manufactured to join steel reinforcing bars of any grade (specified minimum yield strength), uncoated or coated.
1.3This standard describes only the methods for testing mechanical splices for steel reinforcing bars, but does not quantify the parameters for testing nor acceptance criteria, which must be specified.
Note 1:Various code-writing bodies specify various parameters, such as test loads, number of cycles and test temperature, for testing.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 83 : 2023 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 2000 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 83 : 2016 | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 83 : 1998 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM E 466 : 2015 : REDLINE | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
| ASTM E 466 : 1996 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 9 : 2009 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
| ASTM E 466 : 2021 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
| ASTM E 466 : 2015 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM A 370 : 2011 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 467 : 2008 : R2014 | Standard Practice for Verification of Constant Amplitude Dynamic Forces in an Axial Fatigue Testing System |
| ASTM E 9 : 1989 : REV A : R1995 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 467 : 2021 | Standard Practice for Verification of Constant Amplitude Dynamic Forces in an Axial Fatigue Testing System |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.