ASTM A 1008/A1008M : 2023 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable
Hardcopy , PDF
05-20-2024
English
12-29-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
12
|
| ProductNote |
ε1 NOTE—Footnote I in Table 1 was corrected editorially in December 2023.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, required hardness, full hard, solution hardened, and bake hardenable steel sheet, in coils and cut lengths.
1.2Cold rolled steel sheet is available in the designations as listed in 4.1.
1.3This specification does not apply to steel strip as described in Specification A109/A109M.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 917 : 2008 : R2020 | Standard Specification for Steel Sheet, Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface (General Requirements) |
| ASTM F 821/F821M : 2023 | Standard Specification for Domestic Use Doors and Frames, Steel, Interior, Marine |
| ASTM A 599/A599M : 2007 : R2017 | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet |
| ASTM F 823 : 2022 | Standard Specification for Desk, Log, Marine, Steel, with Cabinet |
| ASTM F 1178 : 2011 : R2022 | Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture |
| ASTM A 513/A513M : 2020 : REV A | Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing |
| ASTM A 1092 : 2015 : R2020 | Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet |
| ASTM F 825 : 2022 | Standard Specification for Drawers, Furniture, Marine, Steel |
| ASTM A 568/A568M : 2019 : REV A | Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for |
| ASTM F 1244 : 2008 : R2023 | Standard Specification for Berths, Marine |
| ASTM F 1018 : 2022 | Standard Specification for Steel Emergency Gear Stowage Locker |
| ASTM C 1423 : 2021 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ASTM F 2562/F2562M : 2015 : R2019 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM D 609 : 2017 : R2022 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM F 2408 : 2016 : R2023 | Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets |
| ASTM F 2435 : 2022 | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM A 749/A749M : 2014 : R2021 | Standard Specification for Steel, Strip, Carbon and High-Strength, Low-Alloy, Hot-Rolled, General Requirements for |
| ASTM C 754 : 2020 | Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products |
| ASTM F 822 : 2022 | Standard Specification for Chest of Drawers (Chiffonier), Steel, Marine |
| ASTM F 1267 : 2018 : R2023 | Standard Specification for Metal, Expanded, Steel |
| ASTM F 2432 : 2012 : R2018 | Standard Specification for Ice Making Machines, Icemaker-Dispensers, and Ice Dispensing Equipment |
| ASTM A 879/A879M : 2022 | Standard Specification for Steel Sheet, Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface |
| ASTM C 361M : 2022 | Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric) |
| ASTM C 361 : 2022 | Standard Specification for Reinforced Concrete Low-Head Pressure Pipe |
| ASTM F 826 : 2022 | Standard Specification for Tops, Furniture, Marine, Steel |
| ASTM F 824 : 2022 | Standard Specification for Tables, Mess, Marine, Steel |
| ASTM A 794/A794M : 2024 | Standard Specification for Commercial Steel (CS), Sheet, Carbon (0.16 % Maximum to 0.25 % Maximum), Cold-Rolled |
| ASTM F 2562/F2562M : 2024 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM E 18 : 2024 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 109/A109M : 2024 | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM A 941 : 2023 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 517 : 2019 | Standard Test Method for Plastic Strain Ratio <emph type="bdit">r</emph> for Sheet Metal |
| ASTM A 109/A109M : 2016 : R2018 | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2024 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM E 517 : 2024 | Standard Test Method for Plastic Strain Ratio <emph type="bdit">r</emph> for Sheet Metal |
| ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.