AS/NZS 2642.2:1994

1 - AS/NZS 2642.2:1994 POLYBUTYLENE PIPE SYSTEMS - POLYBUTYLENE (PB) PIPE FOR HOT AND COLD WATER APPLICATIONS
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - 1 SCOPE
7 - 2 REFERENCED DOCUMENTS
8 - 3 DEFINITIONS
8 - 4 HOOP STRESS
8 - 5 CLASSIFICATION
8 - 6 WORKING PRESSURE ACCORDING TO TEMPERATURE RATING
8 - 7 COMPOUND
9 - 8 GENERAL REQUIREMENTS
9 - 8.1 Diameter and wall thickness
9 - 8.2 Length
9 - 8.3 Freedom from defects
9 - 8.4 Toxicity and effect on water
9 - 8.5 Light transmittance
9 - 9 PERFORMANCE REQUIREMENTS
9 - 9.1 General
9 - 9.2 Long-term pressure test
11 - 9.3 Short-term pressure test
11 - 10 PACKAGING
11 - 11 MARKING
12 - APPENDIX A - LONG-TERM PRESSURE TEST
12 - A1 SCOPE
12 - A2 PRINCIPLE
12 - A3 APPARATUS
13 - A4 PREPARATION OF TEST SPECIMENS
13 - A5 REFERENCE POINTS
13 - A6 CONDITIONING OF TEST SPECIMENS
13 - A7 PROCEDURE
15 - A8 TEST REPORT
16 - APPENDIX B - SHORT-TERM PRESSURE TEST
16 - B1 SCOPE
16 - B2 PRINCIPLE
16 - B3 APPARATUS
16 - B4 PREPARATION OF TEST SPECIMENS
16 - B5 CONDITIONING OF TEST SPECIMENS
16 - B6 PROCEDURE
17 - B7 TEST REPORT

Specifies materials, dimensions and performance requirements for polybutylene pipe for hot and cold water applications, including domestic, industrial and agricultural purposes. Applies to pipes of up to 125 mm nominal outside diameter with a wall thickness no greater than 15 mm but does not apply to a wall thickness of less than 1.6 mm.

This Standard specifies materials, dimensions and performance requirements for polybutylene pipe for hot and cold water applications, including domestic, industrial and agricultural purposes. In the interests of serviceability of the pipe, and irrespective of the calculated minimum wall thickness, this Standard does not apply to a wall thickness of less than 1.6 mm. The Standard applies to pipes of up to 125 mm nominal outside diameter with a wall thickness no greater than 15 mm.NOTES:1 Polybutylene undergoes a crystalline transition after it has cooled from the molten state. As a consequence, pipe manufactured to this Standard will not have achieved its full strength until 10 d after the date of manufacture, i.e. the date stamped on the pipe. Precautions should be taken to ensure that pipe is not released from the manufacturer's control prematurely and installed before gaining full strength.2 Polybutylene pipe manufactured in accordance with this Standard is only considered suitable for use in situations exposed to indirect sunlight if it is stabilized against ultraviolet degradation. The only allowable method of stabilization is by the addition of 2.25 ±0.25% of carbon black. Polybutylene pipe should never be used in situations where pipe is exposed to direct sunlight.3 Polybutylene pipe manufactured in accordance with this Standard is intended to be used with fittings complying with AS/NZS 2642.3. Joining polybutylene pipe by means of solvent cement is not satisfactory.4 Type tests specified in Clauses 8.1, 8.4, 8.5, 9.2 and 9.3 are tests performed to assess compliance of finished product with this Standard. However, it may also be convenient for product manufacturers to use those tests for quality control purposes during manufacture.

First published as AS 2642.2-1984.
Second edition 1989.
Jointly revised and designated as Joint Standard AS/NZS 2642.2:1994.