AS 4049.1-1992

1 - AS 4049.1:1992 PAINTS AND RELATED MATERIALS - ROAD MARKING MATERIALS - SOLVENT-BORNE PAINT - FOR USE WITH DROP-ON-BEADS
4 - PREFACE
5 - FOREWORD
6 - 1 SCOPE
6 - 2 REFERENCED DOCUMENTS
6 - 3 DEFINITIONS
6 - 3.1 Bleeding
6 - 3.2 Luminance factor
6 - 4 CLASSIFICATION
6 - 5 COMPOSITION
6 - 6 TESTING AND PERFORMANCE REQUIREMENTS
6 - 6.1 Condition in the container
6 - 6.2 Residue on sieve
6 - 6.3 Consistency
6 - 6.4 No-pick-up time
6 - 6.5 Colour
6 - 6.6 Specular gloss
7 - 6.7 Luminance factor
7 - 6.8 Resistance to bleeding
7 - 6.9 Field testing
7 - 6.9.1 General
7 - 6.9.2 Degree of wear
7 - 6.9.3 Glass bead retention
7 - 6.10 Storage properties
7 - 7 PACKAGING
7 - 8 LABELLING
8 - APPENDIX A - METHODS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
8 - A1 SCOPE
8 - A2 STATISTICAL SAMPLING
8 - A3 PRODUCT CERTIFICATION
8 - A4 SUPPLIER’S QUALITY SYSTEM
8 - AS OTHER MEANS OF ASSESSMENT
8 - A6 SAMPLING PROCEDURE
8 - A6.1 Equipment
8 - A6.1.1 Containers
8 - A6.2 Precautions
9 - A6.3 Procedure
9 - A6.3.1 General
9 - A6.3.2 Filling
9 - A6.3.3 Holding tanks
9 - A6.3.4 Drums
10 - A6.4 Labelling
11 - APPENDIX B - LIST OF REFERENCED DOCUMENTS
12 - APPENDIX C - PREPARATION OF TEST PANELS
12 - C1 SCOPE
12 - C2 TEST PANEL MATERIAL
12 - C3 PAINT APPLICATION
12 - APPENDIX D - DETERMINATION OF LUMINANCE FACTOR
12 - D1 SCOPE
12 - D2 PRINCIPLE
12 - D3 APPARATUS AND MATERIALS
12 - D3.1 Calibrated white standard reference tile
12 - D3.2 Test panel
12 - D3.3 Colorimeter or spectrophotometer
12 - D4 PROCEDURE
12 - D5 CALCULATION
12 - D6 TEST REPORT
13 - APPENDIX E - ASSESSMENT OF RESISTANCE TO BLEEDING OF ROAD MARKING PAINT
13 - E1 SCOPE
13 - E2 PRINCIPLE
13 - E3 REAGENTS
13 - E3.1 Acetone
13 - E4 APPARATUS
13 - E4.1 Draw-down applicator
13 - E4.2 Wire brush
13 - E4.3 Adhesive tape
13 - E4.4 Oven
13 - E4.5 Lint-free cloth
13 - E4.6 Test Panels
13 - E5 TEST PROCEDURE
13 - E6 TEST REPORT
14 - APPENDIX F - FIELD TESTS FOR ROAD MARKING PAINT
14 - F1 SCOPE
14 - F2 PRINCIPLE
14 - F3 TEST SITE
14 - F4 APPARATUS
14 - F4.1 Paint application
14 - F4.2 Assessment of bead retention
14 - F4.3 Assessment of wear using photographic method (Method A)
14 - F4.4 Assessment of wear using grid method (Method B)
14 - F5 APPLICATION PROCEDURE
15 - F6 ASSESSMENT PROCEDURE
15 - F6.1 Bead retention
15 - F6.2 Degree of wear
15 - F6.3 Method A - Photographic method
15 - F6.4 Method B - Grid method
16 - F7 REPORT
21 - APPENDIX G - FIELD DATA SHEET
21 - G1 SCOPE

Provides requirements for solvent-borne paints for road markings and bituminous and concrete road surfaces.

This Standard sets out requirements for solvent-borne paints as used for line markings on bituminous and concrete road surfaces. The Standard is applicable to paints intended for use by spray application (see Note 1). It is also applicable to slower drying paints (see Clause 4) which may be applied by brush or roller. All paints are suitable for use with drop-on beads complying with AS 2009.NOTES:1 Spraying may be by air-atomizing or airless application processes.2 Alternative means for determining compliance with this Standard are given in Appendix A.

First published as AS K146-1967.
Revised and redesignated AS 4049.1-1992.