AS 1597.2-1996
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Precast reinforced concrete box culverts Large culverts (from 1500 mm span and up to and including 4200 mm span and 4200 mm height)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
07-04-2024
English
04-05-1996
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Specifies requirements for the design, testing, manufacture and installation of precast reinforced concrete rectangular box culverts, for conveying water not under pressure and for carrying roadway and railway loadings.
| Committee |
CE/26
|
| DocumentType |
Standard
|
| ISBN |
0 7337 0267 8
|
| Pages |
82
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
This Standard sets out minimum requirements for the design, testing, manufacture and installation of precast reinforced concrete rectangular box culverts for conveying water not under pressure, and for carrying roadway and railway loadings permitted by Australian road and railway authorities.Design requirements are based on the methods of limit state design, using theoretical strength and serviceability calculations, or prototype testing.This Standard is applicable to rectangular precast culvert units having a maximum length of 3600 mm, a maximum height of 4200 mm and a span from 1500 mm to 4200 mm and having a height of fill over the top of the culvert unit not exceeding 10 m.NOTES:1 Guidelines to purchasers on requirements that may need to be agreed upon at the time of calling for tenders or quotations are detailed in Appendix A.2 Methods for demonstrating compliance with this Standard are given in Appendix B.3 For precast reinforced box culverts of internal dimensions exceeding 4200 mm span or height, additional design considerations may be necessary. Additional design considerations are required for special culverts, e.g. skewed ends, culvert units with large holes, culverts subject to loading other than standard roadways and railways loadings.
First published as AS 1597.2-1996.
| AS 3582.3-1994 | Supplementary cementitious materials for use with portland cement - Silica fume |
| AS 1289.5.1.1-2003 | Methods of testing soils for engineering purposes Soil compaction and density tests - Determination of the dry density/moisture content relation of a soil using standard compactive effort |
| AS 1289.5.4.1-2007 | Methods of testing soils for engineering purposes Soil compaction and density tests - Compaction control test - Dry density ratio, moisture variation and moisture ratio (Reconfirmed 2016) |
| AS 1478-1992 | Chemical admixtures for concrete |
| AS 3582.2-2001 | Supplementary cementitious materials for use with portland and blended cement Slag - Ground granulated iron blast-furnace |
| AS 3600-2001 | Concrete structures |
| AS/NZS ISO 9004.1:1994 | Quality management and quality system elements Guidelines |
| AS 1302-1991 | Steel reinforcing bars for concrete |
| AS/NZS ISO 8402:1994 | Quality management and quality assurance - Vocabulary |
| AS 1289.E5.1-1977 | Methods of testing soil for engineering purposes Soil compaction and density tests - Determination of minimum and maximum dry density of a cohesionless material |
| AS 1304-1991 | Welded wire reinforcing fabric for concrete |
| AS 1303-1991 | Steel reinforcing wire for concrete |
| AS 1289.5.3.2-2004 | Methods of testing soils for engineering purposes Soil compaction and density tests - Determination of the field density of a soil - Sand replacement method using a sand pouring can, with or without a volume displacer (Reconfirmed 2016) |
| AS/NZS ISO 9000.1:1994 | Quality management and quality assurance standards Guidelines for selection and use |
| AS 1289.E6.1-1981 | Methods of testing soil for engineering purposes Soil compaction and density tests - Compaction control test - Density index method for a cohesionless material |
| AS 1379-2007 | Specification and supply of concrete (Reconfirmed 2017) |
| AS 1012.9-1999 | Methods of testing concrete Determination of the compressive strength of concrete specimens |
| AS 1726-1993 | Geotechnical site investigations |
| AS 1379-1997 | Specification and supply of concrete |
| AS 1289.5.4.1-1993 | Methods of testing soils for engineering purposes Soil compaction and density tests - Compaction control test - Dry density ratio, moisture variation and moisture ratio |
| AS 3582.2-1991 | Supplementary cementitious materials for use with portland cement Slag - Ground granulated iron blast-furnace |
| AS 1399-1990 | Guide to AS 1199 - Sampling procedures and tables for inspection by attributes |
| AS 1012.1-1993 | Methods of testing concrete Sampling of fresh concrete |
| AS 1199-1988 | Sampling procedures and tables for inspection by attributes |
| HB 18.28-2005 | Conformity assessment - Guidance on a third-party certification system for products |
| AS 3600-1994 | Concrete structures |
| AS 2758.1-1998 | Aggregates and rock for engineering purposes - Concrete aggregates |
| AS 1289.E3.5-1982 | Methods of testing soil for engineering purposes Soil compaction and density tests - Determination of the field dry density of a soil - Water replacement method |
| AS 1289.5.3.2-1993 | Methods of testing soils for engineering purposes Soil compaction and density tests - Determination of the field dry density of a soil - Sand replacement method using a sand pouring can, with or without a volume displacer |
| AS 3582.1-1998 | Supplementary cementitious materials for use with portland and blended cement Fly ash |
| AS 1012.8-1986 | Methods of testing concrete Method for making and curing concrete compression, indirect tensile and flexure test specimens, in the laboratory or in the field |
| AS 1289.5.1.1-1993 | Methods of testing soils for engineering purposes Soil compaction and density tests - Determination of the dry density/moisture content relation of a soil using standard compactive effort |
| AS 3972-1997 | Portland and blended cements |
| AS 1289.C6.1-1977 | Methods of testing soil for engineering purposes Soil classification tests - Determination of the particle size distribution of a soil - Standard method of analysis by sieving |
| AS/NZS 3582.3:2002 | Supplementary cementitious materials for use with portland and blended cement Amorphous silica |
| AS 5100.5-2004 | Bridge design Concrete |
| AS 1597.1-2010 | Precast reinforced concrete box culverts Small culverts (not exceeding 1200 mm span and 1200 mm height) |
| AS 1597.2 SUPP 1-1997 | Precast reinforced concrete box culverts Large culverts (from 1500 mm span and up to and including 4200 mm span and 4200 mm height) - Commentary (Supplement to AS 1597.2-1996) |
| AS 5100.3-2004 | Bridge design Foundations and soil supporting structures |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.