Methods for impact tests on metals Charpy V-notch

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Superseded by

AS 1544.2-2003

Language(s)

English

Published date

01-01-1989

Publisher

Standards Australia

US$27.81

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

1 - AS 1544.2-1989 METHODS FOR IMPACT TESTS ON METALS - CHARPY V-NOTCH
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - 1 SCOPE.
7 - 2 REFERENCED DOCUMENTS.
7 - 3 DEFINITIONS.
7 - 3.1 Centre of percussion
7 - 3.2 Initial potential energy
7 - 3.3 Length of pendulum
7 - 3.4 Point of impact
7 - 3.5 Sample
7 - 3.6 Secondary standard test pieces
7 - 3.7 Standardized test pieces
7 - 3.8 Striking energy
7 - 3.9 Striking velocity
7 - 3.10 Test piece
7 - 3.11 Test specimen
7 - 3.12 Verification
7 - 4 TESTING MACHINE.
7 - 4.1 General.
7 - 4.2 Installation, calibration and maintenance.
7 - 4.3 Test piece supports.
8 - 4.4 Striker.
8 - 4.5 Test piece clearance.
8 - 4.6 Centre of percussion.
8 - 4.7 Striking velocity.
8 - 4.8 Striking energy.
8 - 4.9 Indicating equipment.
9 - 4.10 Zero reading.
9 - 4.11 Friction losses.
9 - 4.12 Initial potential energy.
9 - 4.13 Indicated absorbed energy.
9 - 5 TEST PIECE.
9 - 5.1 Sampling and preparation.
9 - 5.2 Form of test piece.
10 - 5.3 Notch preparation.
10 - 6 PROCEDURE.
10 - 6.1 Conditioning of test piece.
10 - 6.2 Location of test piece.
10 - 6.3 Operation of the testing machine.
10 - 6.4 Record of test results.
10 - 7 REPORT.
12 - APPENDIX A - INSTALLATION, CALIBRATION AND MAINTENANCE OF THE TESTING MACHINE
12 - A1 INSTALLATION.
12 - A1.1 Foundation.
12 - A1.2 Level.
12 - A2 CALIBRATION.
12 - A2.1 Calibration on installation.
12 - A2.2 Routine recalibration of the testing machine.
12 - A2.3 Additional recalibration of the testing machine.
12 - A2.4 Verification.
12 - A2.5 Verification after replacement of striker or anvil parts.
13 - A3 MAINTENANCE OF THE TESTING MACHINE BY THE USER.
13 - A3.1 General.
13 - A3.2 Inspection of components and operation.
13 - A3.3 Test piece locating device.
13 - A3.4 Zero reading.
13 - A3.5 Friction losses.
15 - APPENDIX B - RECORD OF TEST RESULTS

Specifies procedures for carrying out tests and includes description of test pieces, requirements for installation, calibration and verification, and maintenance of the testing machine.

Committee	MT-006
DocumentType	Standard
ISBN	0 7262 5477 0
Pages	9
PublisherName	Standards Australia
Status	Superseded
SupersededBy	AS 1544.2-2003
Supersedes	AS 1544.2-1975
UnderRevision	DR 03088 CP DR 03087

This Standard specifies the conditions for performing the Charpy V-notch impact test on metals, with particular reference to ferrous metals. It also includes requirements for the installation of the testing machine, its initial and periodic calibration, and recommendations for its maintenance by the user.

Under Revision see DR 03087

AS 1444-1996	Wrought alloy steels - Standard, hardenability (H) series and hardened and tempered to designated mechanical properties
AS 2885.2-2002	Pipelines - Gas and liquid petroleum - Welding
AS 1831-2002	Ductile cast iron
AS 2885.2-1995	Pipelines - Gas and liquid petroleum Welding
AS 3597-1993	Structural and pressure vessel steel - Quenched and tempered plate
AS 1163-1991	Structural steel hollow sections
AS 2885.1-1997	Pipelines - Gas and liquid petroleum Design and construction
AS/NZS 1553.1:1995	Covered electrodes for welding - Low carbon steel electrodes for manual metal-arc welding of carbon steels and carbon-manganese steels
AS 3992-1992	Boilers and pressure vessels - Welding and brazing qualification
AS 1833-2002	Austenitic cast iron
AS 2074-2003	Cast steels
AS 4041-1992	Pressure piping
AS 1858.1-2003	Electrodes and fluxes for submerged-arc welding Carbon steels and carbon-manganese steels
AS/NZS 1559:1997	Hot-dip galvanized steel bolts and associated nuts and washers for tower construction
AS/NZS 3679.1:1996	Structural steel Hot-rolled bars and sections
AS 1210-1997	Pressure vessels
AS 2205.7.1-2003	Methods for destructive testing of welds in metal Charpy V-notch impact fracture toughness test
AS 1548-1995	Steel plates for pressure equipment
AS/NZS 1553.2:1999	Covered electrodes for welding - Low and intermediate alloy steel electrodes for manual metal-arc welding of carbon steels and low and intermediate alloy steels
AS/NZS 3678:1996	Structural steel - Hot-rolled plates, floorplates and slabs
AS 3850.2-1990	Tilt-up concrete and precast concrete elements for use in buildings - Guide to design, casting and erection of tilt-up panels
AS 3850-2003	Tilt-up concrete construction

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Shopping Cart

AS 1544.2-1989

Methods for impact tests on metals Charpy V-notch

Table of Contents

Abstract

General Product Information

Scope

History

Standards Referencing This Book

Category

Subcategory