AS 1214-1983
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
06-30-2017
English
01-01-1983
Specifies requirements for the mass, quality, and testing of hot-dip galvanized coating on steel bolts, screws, nuts and other fasteners having ISO metric coarse threads, in the nominal size range M8 to M36 inclusive. Guidance is also given for oversize tapping allowances for fasteners, with metric coarse threads up to and including M64 diameter.
Committee |
ME-029
|
DocumentType |
Standard
|
ISBN |
0 7262 2825 7
|
Pages |
5
|
PublisherName |
Standards Australia
|
Status |
Superseded
|
SupersededBy | |
Supersedes | |
UnderRevision |
This standard specifies requirements for the mass, quality and testing of hot-dip galvanized coating on steel bolts, screws, nuts and other fasteners having ISO metric coarse threads, in the nominal size range M8 to M36 inclusive.It deals with the purity of the galvanizing bath, the appearance of the coating under visual examination, the mass of the coating, the adhesion of the coating, and the test methods to be adopted. It also deals with the oversize tapped screw thread limits for internal threads, but does not deal with other dimensions, depending for these on reference to relevant specifications.After galvanizing, fasteners must comply with the physical property requirements of their relevant specifications when tested in accordance with requirements specified therein.NOTES:1. The term 'relevant specification' refers to a specification covering the dimensions and physical properties of metric fasteners as required by the purchaser. This may be an Australian standard (e.g. AS 1110, 1111, 1112) or any other specification cited by the purchaser.2. ISO metric coarse threads below M8 and all ISO metric fine pitch threads, generally cannot be successfully hot-dip galvanized without difficulty with regard to the assembly of bolt and nut.3. This standard does not specify a requirement for uniformity of coating. Guidance is given in Appendix D.
Standards | Relationship |
ISO 1460:1973 | Identical |
ISO 1461:1973 | Identical |
AS 1721-1985 | General purpose metric screw threads (Reconfirmed 2017) |
AS 1275-1985 | |
AS/NZS 1112:1996 | ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts |
AS 2331.2.1-2001 | Methods of test for metallic and related coatings Tests for average coating mass per unit area or for thickness - Dissolution methods - Strip and weigh, and analytical |
AS 1650-1989 | Hot-dipped galvanized coatings on ferrous articles |
AS 2331.1.3-2001 | Methods of test for metallic and related coatings Local thickness tests - Magnetic method (Reconfirmed 2017) |
AS 2331.2.3-2001 | Methods of test for metallic and related coatings Tests for average coating mass per unit area or for thickness - Hydrogen evolution method for zinc coatings |
AS/NZS 1111:1996 | ISO metric hexagon commercial bolts and screws |
AS/NZS 1110:1995 | ISO metric precision hexagon bolts and screws |
AS 1684.3-2010 | Residential timber-framed construction Cyclonic areas |
AS 1684.4-2010 | Residential timber-framed construction Simplified - Non-Cyclonic Areas |
AS 4087-2004 | Metallic flanges for waterworks purposes |
AS 4087-1993 | Metallic flanges for waterworks purposes |
AS 1684.2-2010 | Residential timber-framed construction Non-cyclonic areas |
AS 2309-2008 | Durability of galvanized and electrogalvanized zinc coatings for the protection of steel in structural applications - Atmospheric |
AS/NZS 2041.6:2010 | Buried corrugated metal structures Bolted plate structures |
AS 1275-1985 | |
AS 2319-2001 | Rigging screws and turnbuckles |
AS/NZS 1768:2007 | Lightning protection |
AS 1684-1992 | National Timber Framing Code |
AS 1768-1991 | Lightning protection |
AS/NZS 1390:1997 | Cup head bolts with ISO metric coarse pitch threads (Reconfirmed 2016) |
AS 1154.3-2009 | Insulator and conductor fittings for overhead power lines Performance and general requirements for helical fittings (Reconfirmed 2019) |
AS/NZS 4396:1999 | Connectors - Insulation piercing - For 0.6/1 kV aerial bundled cables |
AS 1154.1-2009 | Insulator and conductor fittings for overhead power lines Performance, material, general requirements and dimensions (Reconfirmed 2019) |
AS/NZS 4998:2009 | Bolted unrestrained mechanical couplings for waterworks purposes (Reconfirmed 2022) |
AS 1684.2-2006 | Residential timber-framed construction Non-cyclonic areas (SEE IMPORTANT NOTE) |
AS 1721-1985 | General purpose metric screw threads (Reconfirmed 2017) |
AS 4087-1996 | Metallic flanges for waterworks purposes |
AS 2144:2014 | Traffic signal lanterns |
AS 4087:2011 | Metallic flanges for waterworks purposes |
AS/NZS 2947.2:2002 | Insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c. |
AS/NZS 1252:1996 | High-strength steel bolts with associated nuts and washers for structural engineering |
AS 4899-2007 | Pin insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c. (Reconfirmed 2018) |
AS 4795.1-2011 | Butterfly valves for waterworks purposes Wafer and lugged (Reconfirmed 2022) |
AS 5100.8:2017 | Bridge design Rehabilitation and strengthening of existing bridges |
AS/NZS 2947.1:1999 | Insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c. Test methods - Insulator units |
AS 2339-1997 | Traffic signal posts and attachments |
AS 4795-2002 | Double-flanged butterfly valves for waterworks purposes |
AS/NZS 1112:1996 | ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts |
AS/NZS 2312:2002 | Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings |
AS/NZS 1559:1997 | Hot-dip galvanized steel bolts and associated nuts and washers for tower construction |
AS/NZS 3845:1999 | Road safety barrier systems |
AS/NZS 2041.4:2010 | Buried corrugated metal structures Helically formed sinusoidal pipes |
AS 4398.1-1996 | Insulators - Ceramic or glass - Station post for indoor and outdoor use - Voltages greater than 1000 V a.c. Characteristics (Reconfirmed 2016) |
AS/NZS 1111:1996 | ISO metric hexagon commercial bolts and screws |
AS 2528-1982 | Bolts, studbolts and nuts for flanges and other high and low temperature applications |
AS 1154.1-2004 | Insulator and conductor fittings for overhead power lines - Performance, material, general requirements and dimensions |
AS IEC 62155-2005 | Insulators - Ceramic or glass - Hollow pressurized and unpressurized - Voltages greater than 1000 V a.c. (Reconfirmed 2016) |
AS 4795-2006 | Butterfly valves for waterworks purposes |
AS 2933-1987 | Shipbuilding - Pilot ladders |
AS/NZS 4680:2006 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles (Reconfirmed 2017) |
AS 2143-1978 | Industrial and commercial steel shelving |
AS 1154.3-1985 | Insulator and conductor fittings for overhead power lines - Performance and general requirements for helical fittings |
AS 3703.1-1989 | Long-span corrugated steel structures - Materials and manufacture |
AS 5612-2013 | Butterfly valves for general purposes |
AS 2144-1995 | Traffic signal lanterns |
AS/NZS 1891.2:2001 | Industrial fall-arrest systems and devices Horizontal lifeline and rail systems |
AS 3766-1990 | Mechanical fittings for low voltage aerial bundled cables |
AS/NZS 1110:1995 | ISO metric precision hexagon bolts and screws |
AS 2273-1979 | Steel library shelving |
AS 4398.2-1996 | Insulators - Ceramic or glass - Station post for indoor and outdoor use - Voltages greater than 1000 V a.c. Tests |
AS 4398.2-2005 | Insulators - Ceramic or glass - Station post for indoor or outdoor use - Voltages greater than 1000 V a.c. Tests (IEC 60168, Ed. 4.2 (2001) MOD) |
AS 2339:2017 | Traffic signal posts, mast arms and attachments |
AS 1562.1-1992 | Design and installation of sheet roof and wall cladding Metal (Reconfirmed 2016) |
AS/NZS 2312:1994 | Guide to the protection of iron and steel against exterior atmospheric corrosion |
AS/NZS 1891.2(INT):1998 | Industrial fall-arrest systems and devices - Horizontal lifeline and rail systems |
AS 4285-1995 | Skylights |
AS 4285-2007 | Skylights |
AS 1684.3-2006 | Residential timber-framed construction Cyclonic areas |
AS/NZS 4680:1999 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles |
AS/NZS 2041:1998 | Buried corrugated metal structures |
AS/NZS 1768(INT):2003 | Lightning protection |
AS/NZS 4396(INT):1996 | Connectors - Insulation piercing - For 0.6/1 kV aerial bundled cables |
AS/NZS 2144:2002 | Traffic signal lanterns |
AS 2979-1998 | Traffic signal mast arms |
AS 1684.4-2006 | Residential timber-framed construction - Simplified Non-cyclonic areas (SEE IMPORTANT NOTE) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.