API 677 : 2006 : R2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GENERAL-PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
Hardcopy , PDF
02-22-2021
English
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 GENERAL
2 BASIC DESIGN
3 ACCESSORIES
4 INSPECTION, TESTING, AND PREPARATION FOR SHIPMENT
5 VENDOR'S DATA
APPENDIX A - GENERAL-PURPOSE GEAR DATA SHEETS
APPENDIX B - LATERAL CRITICAL SPEED MAP AND MODE
SHAPES FOR A TYPICAL ROTOR
APPENDIX C - TYPICAL LUBE-OIL SYSTEMS
APPENDIX D - MATERIAL SPECIFICATIONS FOR
GENERAL-PURPOSE GEAR UNITS PAGE
APPENDIX E - VENDOR DRAWING AND DATA REQUIREMENTS
APPENDIX F - REFERENCED SPECIFICATIONS
APPENDIX G - SPIRAL BEVEL GEAR-TOOTH CONTACT
ARRANGEMENT REQUIREMENTS FOR INSPECTION
APPENDIX H - RESIDUAL UNBALANCE WORKSHEETS
Defines the minimum requirements for general-purpose, enclosed single and multistage gear units incorporating parallel shaft helical and right angle spiral bevel gears for the petroleum, chemical, and gas industries.
| DocumentType |
Standard
|
| Pages |
104
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
American Petroleum Institute
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| AGMA 9002 : B | BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS (INCH SERIES) |
| AGMA 6011 : I | SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| AGMA 6025 : D | SOUND FOR ENCLOSED HELICAL, HERRINGBONE AND SPIRAL BEVEL GEAR DRIVES |
| NEMA SM 23-1991 (R1997, R2002) | STEAM TURBINES FOR MECHANICAL DRIVE SERVICE |
| AGMA 2101 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION) |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ISO 1328-1:2013 | Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| AGMA 6010 : F | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| NEMA 250 : 2014 | ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM) |
| ASME B16.42 : 2016 | DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300 |
| ASME B31.3:2016 | PROCESS PIPING |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| AGMA 6001 : D | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| AGMA 908 : B | GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| ISO 5753:1991 | Rolling bearings — Radial internal clearance |
| API 686 : 2009 | RECOMMENDED PRACTICE FOR MACHINERY INSTALLATION AND INSTALLATION DESIGN |
| EN 10084:2008 | Case hardening steels - Technical delivery conditions |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
| ISO/TR 10064-1:2017 | Code of inspection practice Part 1: Measurement of cylindrical gear tooth flanks |
| EN 1561:2011 | Founding - Grey cast irons |
| ISO/R 286:1962 | ISO system of limits and fits Part I : General, tolerances and deviations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.