ANSI S12.54:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
Hardcopy , PDF
English
01-01-2016
07-13-2019
1 Scope
2 Normative references
3 Terms and definitions
4 Test environment
5 Instrumentation
6 Definition, location, installation, and
operation of noise source under test
7 Reference box and measurement surface
8 Determination of sound power levels and
sound energy levels
9 Measurement uncertainty
10 Information to be recorded
11 Test report
Annex A (normative) - Qualification procedures for
the acoustic environment
Annex B (normative) - Microphone arrays on a
hemispherical measurement surface
Annex C (normative) - Microphone arrays on a
parallelepiped measurement surface
Annex D (informative) - Microphone arrays on a
cylindrical measurement surface
Annex E (normative) - Calculation of A-weighted
sound power levels and A-weighted sound
energy levels from frequency band levels
Annex F (normative) - Alternative microphone
array on a hemispherical measurement surface
for direct measurements of A-weighted
sound pressure levels
Annex G (normative) - Sound power level and
sound energy level under reference
meteorological conditions
Annex H (informative) - Guidelines on the development
of information on measurement
uncertainty
Bibliography
Describes methods for determining the sound power level or sound energy level of a noise source from sound pressure levels measured on a surface enveloping the noise source (machinery or equipment) in an environment that approximates to an acoustic free field near one or more reflecting planes.
| Committee |
S12
|
| DevelopmentNote |
Also numbered as ISO 3744. (09/2003) Supersedes ANSI S12.34 (02/2006)
|
| DocumentType |
Standard
|
| Pages |
100
|
| ProductNote |
Reconfirmed 2011
|
| PublisherName |
Acoustical Society of America
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ANSI NEMA MG 00001:2024 | Motors and Generators |
| ISO 7574-2:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 2: Methods for stated values for individual machines |
| ISO 13472-1:2002 | Acoustics — Measurement of sound absorption properties of road surfaces in situ — Part 1: Extended surface method |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 12001:1996 | Acoustics — Noise emitted by machinery and equipment — Rules for the drafting and presentation of a noise test code |
| ISO 3743-2:1994 | Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms |
| ISO 3382-2:2008 | Acoustics — Measurement of room acoustic parameters — Part 2: Reverberation time in ordinary rooms |
| ISO 7574-4:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 4: Methods for stated values for batches of machines |
| ISO/TR 25417:2007 | Acoustics — Definitions of basic quantities and terms |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| IEC 60942:2003 | Electroacoustics - Sound calibrators |
| ISO 9296:2017 | Acoustics — Declared noise emission values of information technology and telecommunications equipment |
| ISO 3747:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering/survey methods for use in situ in a reverberant environment |
| ISO 3740:2000 | Acoustics — Determination of sound power levels of noise sources — Guidelines for the use of basic standards |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ISO 7574-1:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 1: General considerations and definitions |
| ISO 80000-8:2007 | Quantities and units — Part 8: Acoustics |
| ISO 3746:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 6926:2016 | Acoustics — Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels |
| ISO 9614-3:2002 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning |
| ISO 10534-2:1998 | Acoustics — Determination of sound absorption coefficient and impedance in impedance tubes — Part 2: Transfer-function method |
| ISO 7574-3:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 3: Simple (transition) method for stated values for batches of machines |
| ISO 3741:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for reverberation test rooms |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| IEC 61260:1995 | Electroacoustics - Octave-band and fractional-octave-band filters |
| ISO 10534-1:1996 | Acoustics — Determination of sound absorption coefficient and impedance in impedance tubes — Part 1: Method using standing wave ratio |
| ISO 11201:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
| ISO 3743-1:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.