AGMA 1012 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
Hardcopy
08-15-2023
English
01-01-2005
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and symbols
4 Geometric definitions
4.1 General designations
4.2 Kinds of gears
4.3 Principal planes
4.4 Principal directions
4.5 Surfaces and dimensions
4.6 Terms related to gear teeth
4.7 Terms related to gear pairs
4.8 Terms related to tooth contact in a gear pair
5 Inspection definitions
Annexes
A Abbreviations
B Glossary of trade terms
C Terms and symbols
Bibliography
Index of terms
Presents the definitions of terms, symbols and abbreviations which may be used to communicate the technology and specifications of external and internal gear teeth. It provides definitive meanings by the use of words and illustrations, for commonly used gearing terms.
| DevelopmentNote |
Supersedes AGMA 112.05 and AGMA 116.01 (03/2002) Supersedes AGMA 912. (10/2014)
|
| DocumentType |
Standard
|
| Pages |
80
|
| PublisherName |
American Gear Manufacturers Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| AGMA 1103 : H | TOOTH PROPORTIONS FOR FINE-PITCH SPUR AND HELICAL GEARING (METRIC EDITION) |
| AGMA 940:2009(R2022) | DOUBLE HELICAL EPICYCLIC GEAR UNITS |
| AGMA 938 : A | SHOT PEENING OF GEARS |
| AGMA 6010 : REV F : 1997 : R2003 | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| AGMA 2015-1 : A | ACCURACY CLASSIFICATION SYSTEM - TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS |
| AGMA 1010 : E | APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE |
| AGMA 905 : A2017 | INSPECTION OF MOLDED PLASTIC GEARS |
| AGMA 914 : B | GEAR SOUND MANUAL - PART 1 - FUNDAMENTALS OF SOUND AS RELATED TO GEARS - PART 2 - SOURCES, SPECIFICATIONS AND LEVELS OF GEAR SOUND - PART 3 - GEAR NOISE CONTROL |
| AGMA 935 : A | RECOMMENDATIONS RELATIVE TO THE EVALUATION OF RADIAL COMPOSITE GEAR DOUBLE FLANK TESTERS |
| AGMA 2005 : D | DESIGN MANUAL FOR BEVEL GEARS |
| AGMA 6110 : REV F : 1997 : R2003 | STANDARD FOR SPUR, HELICAL, HERRINGBONE, AND BEVEL ENCLOSED DRIVES |
| AGMA 6010 : REV F : 1997 | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| AGMA 6123 : REV A : 1988 | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| AGMA 1010 : REV E : 1995 : R2004 | APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE |
| AGMA 900 : H | STYLE MANUAL FOR THE PREPARATION OF STANDARDS, INFORMATION SHEETS AND EDITORIAL MANUALS |
| AGMA 915-2 : A | INSPECTION PRACTICES - PART 2: CYLINDRICAL GEARS - RADIAL MEASUREMENTS |
| API SPEC 11E CHINESE : 2013 | SPECIFICATION FOR PUMPING UNITS |
| API 687 : 2001 | ROTOR REPAIR |
| AGMA 2116 : A | EVALUATION OF DOUBLE FLANK TESTERS FOR RADIAL COMPOSITE MEASUREMENT OF GEARS |
| AGMA 2101 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION) |
| AGMA 2001 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH |
| AGMA 940 : A2009(R2017) | DOUBLE HELICAL EPICYCLIC GEAR UNITS |
| 06/30157507 DC : 0 | BS ISO 10431 - PETROLEUM AND NATURAL GAS INDUSTRIES - PUMPING UNITS - SPECIFICATION |
| AGMA 923 : B | METALLURGICAL SPECIFICATIONS OF STEEL GEARING |
| AGMA 6123 : REV A : 2006 | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| API 11E RUSSIAN : 2013 | SPECIFICATION FOR PUMPING UNITS |
| AGMA 1010 : REV E : 1995 | APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE |
| AGMA 6123 : REV A : 1988 : R2000 | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| AGMA 2008 : C | ASSEMBLING BEVEL GEARS |
| AGMA 6010 : F | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| AGMA 937 : A2012(R2017) | AEROSPACE BEVEL GEARS |
| ISO 81400-4:2005 | Wind turbines Part 4: Design and specification of gearboxes |
| API 687 : 2001 : R2009 | ROTOR REPAIR |
| AGMA 1003 : H | TOOTH PROPORTIONS FOR FINE-PITCH SPUR AND HELICAL GEARING |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| API SPEC 11E : 2013 | SPECIFICATION FOR PUMPING UNITS |
| AGMA 6110 : REV F : 1997 | STANDARD FOR SPUR, HELICAL, HERRINGBONE, AND BEVEL ENCLOSED DRIVES |
| BS ISO 81400-4:2005 | Wind turbines Design and specification of gearboxes |
| API 687 : 2001 : R2015 | ROTOR REPAIR |
| ASTM E 2905/E2905M : 2013 : REDLINE | PRACTICE FOR EXAMINATION OF MILL AND KILN GIRTH GEAR TEETH - ELECTROMAGNETIC METHODS |
| AGMA 2015-1 : A | ACCURACY CLASSIFICATION SYSTEM - TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS |
| AGMA 2009 : B | BEVEL GEAR CLASSIFICATION, TOLERANCES AND MEASURING METHODS |
| AGMA 2003 : B | RATING THE PITTING RESISTANCE AND BENDING STRENGTH OF GENERATED STRAIGHT BEVEL, ZEROL BEVEL AND SPIRAL BEVEL GEAR TEETH |
| ISO 701:1998 | International gear notation Symbols for geometrical data |
| AGMA 2000 : A | GEAR CLASSIFICATION AND INSPECTION HANDBOOK - TOLERANCES AND MEASURING METHODS FOR UNASSEMBLED SPUR AND HELICAL GEARS (INCLUDING METRIC EQUIVALENTS) |
| AGMA 2101 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION) |
| AGMA 2005 : D | DESIGN MANUAL FOR BEVEL GEARS |
| AGMA 913 : A | METHOD FOR SPECIFYING THE GEOMETRY OF SPUR AND HELICAL GEARS |
| AGMA 2002 : B | TOOTH THICKNESS AND BACKLASH MEASUREMENT OF CYLINDRICAL INVOLUTE GEARING |
| AGMA 915-3 : A1999(R2017) | INSPECTION PRACTICES - GEAR BLANKS, SHAFT CENTER DISTANCE AND PARALLELISM |
| AGMA 2001 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.