17/30341312 DC : 0
NA
NA
Status of Standard is Unknown
BS EN ISO 21225-1 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 1: REPLACEMENT ON THE LINE BY PIPE BURSTING AND PIPE EXTRACTION
Available format(s)
Hardcopy , PDF
Language(s)
English
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Design aspects
6 Material selection
7 Installation practice
8 Fitness for purpose
Annex A (normative) - Layered pipes
Annex B (Informative) - Pipe design considerations
particular to pipe bursting and pipe extraction
Bibliography
BS EN ISO 21225-1.
| Committee |
PRI/88/3
|
| DocumentType |
Draft
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| ISO 4437-5:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 5: Fitness for purpose of the system |
| EN 15885:2010 | Classification and characteristics of techniques for renovation and repair of drains and sewers |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| BS PAS 128(2014) : 2014 | SPECIFICATION FOR UNDERGROUND UTILITY DETECTION, VERIFICATION AND LOCATION |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) |
| ISO 4427-1:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 4427-5:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| DVGW GW 312 : 2014 | |
| ISO 16010:2005 | Elastomeric seals Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids |
| DVGW GW 322 : DRAFT 2001 | NO-DIG REPLACEMENT OF GAS AND WATER PIPEWORK USING PUSHING OR PULLING PROCEDURES - REQUIREMENTS, QUALITY AND TESTING |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 4437-1:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 1: General |
| DVGW GW 323 : 2004 COR 2009 | GRABENLOSE ERNEUERUNG VON GAS- UND WASSERVERSORGUNGSLEITUNGEN DURCH BERSTLINING - ANFORDERUNGEN, GUETESICHERUNG UND PRUEFUNG |
| DWA-M 143-15 : 2005 | SANIERUNG VON ENTWAESSERUNGSSYSTEMEN AUSSERHALB VON GEBAEUDEN - TEIL 15: ERNEUERUNG VON ABWASSERLEITUNGEN UND -KANAELEN DURCH BERSTVERFAHREN |
| EN 12889:2000 | Trenchless construction and testing of drains and sewers |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| ISO 4437-3:2014 | Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| NEN 3650-1 : 2012 + C1 2017 | REQUIREMENTS FOR PIPELINE SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| ISO 4633:2015 | Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials |
| DVGW GW 304 : 2008 | |
| ISO 4427-2:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes |
| DVGW GW 325 : 2007 | GRABENLOSE BAUWEISEN FUER GAS- UND WASSER-ANSCHLUSSLEITUNGEN - ANFORDERUNGEN, GUETESICHERUNG UND PRUEFUNG |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.