16/30331025 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 50134-2 - ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 2: TRIGGER DEVICES
Hardcopy , PDF
01-31-2018
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test of manually activated trigger devices
Annex A (normative) - Measurements of contact and insulation
resistances for mechanical contact function
Annex B (normative) - Strain relief test jig
Annex C (normative) - Test set-up by using rf-shielded
test fixtures
Bibliography
BS EN 50134-2.
| Committee |
²GW/1/12
|
| DocumentType |
Draft
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 50134-2 : DRAFT 2016 | Identical |
| IEC 61020-1:2009 | Electromechanical switches for use in electrical and electronic equipment - Part 1: Generic specification |
| EN 50134-5:2004 | Alarm systems - Social alarm systems - Part 5: Interconnections and communications |
| EN 50055:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group I apparatus indicating up to 5 % (v/v) methane in air |
| EN 61020-1:2009 | Electromechanical switches for use in electrical and electronic equipment - Part 1: Generic specification |
| IEC 61779-2:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 2: Performance requirements for group I apparatus indicating a volume fraction up to 5 % methane in air |
| EN 50134-1:2002 | Alarm systems - Social alarm systems - Part 1: System requirements |
| EN 50057:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group II apparatus indicating up to 100 % lower explosive limit |
| IEC 62599-1:2010 | Alarm systems - Part 1: Environmental test methods |
| EN 60447:2004 | Basic and safety principles for man-machine interface, marking and identification - Actuating principles |
| IEC 61779-4:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating up to 100% lower explosive limit |
| EN 303 131 : 1.1.0 DRAFT | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); SHORT RANGE DEVICES; WIRELESS ALARMS WITH LOW DUTY CYCLE; HARMONIZED EN COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE R&TTE DIRECTIVE |
| IEC 62599-2:2010 | Alarm systems - Part 2: Electromagnetic compatibility - Immunity requirements for components of fire and security alarm systems |
| IEC 61779-3:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 3: Performance requirements for group I apparatus indicating a volume fraction up to 100 % methane in air |
| IEC 60477:1974 | Laboratory d.c. resistors |
| IEC 61779-5:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 5: Performance requirements for group II apparatus indicating a volume fraction up to 100 % gas |
| EN 50056:1998 | Electrical apparatus for the detection and measurement of combustible gases - Performance requirements for Group I apparatus indicating up to 100 % (v/v) methane in air |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.