15/30296029 DC : 0
NA
Status of Standard is Unknown
BS ISO 4955 - HEAT-RESISTANT STEELS
Hardcopy , PDF
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Information to be supplied by the purchaser
6 Classification of grades
7 Requirements
8 Inspection, testing and conformance of products
9 Marking
Annex A (informative) - Technical information on heat- and
creep-resistant steels
Annex B (informative) - Data for creep strength to 1 % plastic
strain and creep rupture strength
Annex C (informative) - Designations of the steels given in
and of comparable grades covered in various designation
systems
Annex D (informative) - Applicable dimensional standards
Bibliography
BS ISO 4955.
| Committee |
ISE/105
|
| DocumentType |
Draft
|
| Pages |
48
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| ISO 404:2013 | Steel and steel products — General technical delivery requirements |
| ISO 6929:2013 | Steel products — Vocabulary |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 20723:2004 | Structural steels — Surface condition of hot-rolled sections — Delivery requirements |
| ISO 9444-2:2009 | Continuously hot-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and sheet/plate |
| ISO/TS 4949:2016 | Steel names based on letter symbols |
| ISO/TR 9769:1991 | Steel and iron Review of available methods of analysis |
| ISO 16143-3:2014 | Stainless steels for general purposes — Part 3: Wire |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| ISO 657-11:1980 | Hot-rolled steel sections — Part 11: Sloping flange channel sections (Metric series) — Dimensions and sectional properties |
| ISO 16143-2:2014 | Stainless steels for general purposes — Part 2: Corrosion-resistant semi-finished products, bars, rods and sections |
| ISO 16124:2015 | Steel wire rod — Dimensions and tolerances |
| ISO 657-1:1989 | Hot-rolled steel sections — Part 1: Equal-leg angles — Dimensions |
| ISO 4885:2017 | Ferrous materials Heat treatments Vocabulary |
| ISO 1035-3:1980 | Hot-rolled steel bars — Part 3: Dimensions of flat bars |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 1035-4:1982 | Hot-rolled steel bars — Part 4: Tolerances |
| ISO 16143-1:2014 | Stainless steels for general purposes — Part 1: Corrosion-resistant flat products |
| ISO 17577:2016 | Steel Ultrasonic testing of steel flat products of thickness equal to or greater than 6 mm |
| ISO 683-15:1992 | Heat-treatable steels, alloy steels and free-cutting steels — Part 15: Valve steels for internal combustion engines |
| ISO 657-15:1980 | Hot-rolled steel sections — Part 15: Sloping flange beam sections (Metric series) — Dimensions and sectional properties |
| ISO 1035-1:1980 | Hot-rolled steel bars — Part 1: Dimensions of round bars |
| ISO 9445-2:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet |
| ISO 9444-1:2009 | Continuously hot-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| ISO 1035-2:1980 | Hot-rolled steel bars — Part 2: Dimensions of square bars |
| ISO 657-13:1981 | Hot-rolled steel sections Part 13: Tolerances on sloping flange beam, column and channel sections |
| ISO 657-2:1989 | Hot-rolled steel sections — Part 2: Unequal-leg angles — Dimensions |
| ISO 657-16:1980 | Hot-rolled steel sections Part 16: Sloping flange column sections (metric series) Dimensions and sectional properties |
| ISO 18286:2008 | Hot-rolled stainless steel plates — Tolerances on dimensions and shape |
| ISO 657-21:1983 | Hot-rolled steel sections Part 21: T-sections with equal depth and flange width Dimensions |
| ISO 9445-1:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths |
| ISO 657-5:1976 | Hot-rolled steel sections — Part 5: Equal-leg angles and unequal-leg angles — Tolerances for metric and inch series |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| ISO 9443:1991 | Heat-treatable and alloy steels Surface quality classes for hot-rolled round bars and wire rods Technical delivery conditions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.