15/30294124 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 60674-2 ED 2.0 - SPECIFICATION FOR PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
Hardcopy , PDF
07-31-2017
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative References
3 General notes on tests
4 Thickness
5 Density
6 Width
7 Windability (bias/camber and sag)
8 Surface roughness
9 Space factor
10 Coefficient of friction
11 Wetting tension (polyolefine films)
12 Tensile properties
13 Edge tearing resistance
14 Tear resistance
15 Stiffness of film
16 Surface resistivity
17 Volume resistivity
18 Dissipation factor and permittivity
19 Dissipation factor under impregnated conditions
20 Electric strength
21 Electrical weak spots
22 Resistance to breakdown by surface discharges
23 Electrolytic corrosion
24 Melting point
25 Dimensional change
26 Dimensional stability under tension with rising
temperature
27 Dimensional stability under pressure with rising
temperature
28 Resistance to penetration at elevated temperature
29 Volatile content (loss of mass on heating)
30 Thermal endurance
31 Burning characteristics
32 Water absorption in a damp atmosphere
33 Absorption of liquid
34 Ionic impurities
35 Effect of insulating varnishes
36 Effect of polymerisable resinous compounds in
a liquid state
BS EN 60674-2 Ed 2.0.
| Committee |
GEL/15
|
| DocumentType |
Draft
|
| Pages |
39
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60454-2:2007 | Pressure-sensitive adhesive tapes for electrical purposes - Part 2: Methods of test |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| IEC 60343:1991 | Recommended test methods for determining the relative resistance of insulating materials to breakdown by surface discharges |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| ISO 4591:1992 | Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
| IEC 60394-2:1972 | Varnished fabrics for electrical purposes. Part 2: Methods of test |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| IEC 60216-8:2013 | Electrical insulating materials - Thermal endurance properties - Part 8: Instructions for calculating thermal endurance characteristics using simplified procedures |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 60589:1977 | Methods of test for the determination of ionic impurities in electrical insulating materials by extraction with liquids |
| IEC TR 60648:1979 | Method of test for coefficients of friction of plastic film and sheeting for use as electrical insulation |
| ISO 534:2011 | Paper and board — Determination of thickness, density and specific volume |
| IEC 60243-2:2013 | Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage |
| IEC 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
| ISO 6383-2:1983 | Plastics Film and sheeting Determination of tear resistance Part 2: Elmendorf method |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 4592:1992 | Plastics — Film and sheeting — Determination of length and width |
| IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| ISO 6383-1:2015 | Plastics Film and sheeting Determination of tear resistance Part 1: Trouser tear method |
| ISO 4593:1993 | Plastics Film and sheeting Determination of thickness by mechanical scanning |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.