14/30273161 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 556-2 - STERILIZATION OF MEDICAL DEVICES - REQUIREMENTS FOR MEDICAL DEVICES TO BE DESIGNATED ''STERILE'' - PART 2: REQUIREMENTS FOR ASEPTICALLY PROCESSED MEDICAL DEVICES
Hardcopy , PDF
09-30-2015
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 90/385/EEC on Active Implantable
Medical Devices
Annex ZB (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 93/42/EEC on Medical Devices
Annex ZC (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 98/79/EC on in vitro diagnostic
medical devices
Bibliography
BS EN 556-2.
| Committee |
CH/198
|
| DocumentType |
Draft
|
| Pages |
17
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 556-2 : DRAFT 2014 | Identical |
| ISO 11137-1:2006 | Sterilization of health care products Radiation Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 13408-7:2012 | Aseptic processing of health care products — Part 7: Alternative processes for medical devices and combination products |
| EN ISO 14937:2009 | Sterilization of health care products - General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices (ISO 14937:2009) |
| ISO 14160:2011 | Sterilization of health care products Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives Requirements for characterization, development, validation and routine control of a sterilization process for medical devices |
| EN ISO 13408-3:2011 | Aseptic processing of health care products - Part 3: Lyophilization (ISO 13408-3:2006) |
| EN ISO 13408-4:2011 | Aseptic processing of health care products - Part 4: Clean-in-place technologies (ISO 13408-4:2005) |
| EN ISO 13408-5:2011 | Aseptic processing of health care products - Part 5: Sterilization in place (ISO 13408-5:2006) |
| EN ISO 13408-1:2015 | Aseptic processing of health care products - Part 1: General requirements (ISO 13408-1:2008, including Amd 1:2013) |
| ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
| ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 25424:2009 | Sterilization of medical devices Low temperature steam and formaldehyde Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 11135-1:2007 | Sterilization of health care products Ethylene oxide Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| EN ISO 25424:2011 | Sterilization of medical devices - Low temperature steam and formaldehyde - Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 25424:2009) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 20857:2010 | Sterilization of health care products Dry heat Requirements for the development, validation and routine control of a sterilization process for medical devices |
| EN ISO 11135-1:2007 | Sterilization of health care products - Ethylene oxide - Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 11135-1:2007) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 11137-1:2015 | Sterilization of health care products - Radiation - Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 11137-1:2006, including Amd 1:2013) |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| EN ISO 17665-1:2006 | Sterilization of health care products - Moist heat - Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 17665-1:2006) |
| EN ISO 20857:2013 | Sterilization of health care products - Dry heat - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 20857:2010) |
| EN 980:2008 | Symbols for use in the labelling of medical devices |
| EN ISO 14160:2011 | Sterilization of health care products - Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives - Requirements for characterization, development, validation and routine control of a sterilization process for medical devices (ISO 14160:2011) |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.